Télécharger Imprimer la page

MIRKA AOS-B 130 Manuel D'utilisation page 64

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 282
en (original)
Cordless
Sound pressure level (L
Sound power level (L
WA
Sound measurement uncertainty
K
WA
Vibration emission value a
Vibration emission uncertainty K
*
Specifications subject to change without prior notice. Model range may vary between markets.
*
In order to reflect normal working conditions of the sander the operating conditions did deviate from the standard
method as follows: Grain size of the abrasive was 5 m. Feed force was 10 N.
*
The values stated in the table are derived from laboratory testing in conformity with stated codes and standards and
are not sufficient for risk evaluation. Values measured in a particular work place may be higher than the declared
values. The actual exposure values and amount of risk or harm experienced by an individual are unique to each
situation and depend upon the surrounding environment, the way the individual operates the machinery, the par-
ticular material being worked, work station design and the user's exposure time and physical condition. Mirka accepts
no responsibility for the consequences of using declared values instead of actual exposure values for any individual
risk assessment.
Further occupational health and safety information can be obtained from the following websites:
https://osha.europa.eu/en (Europe) or http://www.osha.gov (USA)
Proper use of tool
This sander is designed for sanding all types of materials such as paints, metals, wood, stone, plastics, etc., using abrasives
specially designed for this purpose. Do not use this sander for any other purpose than that specified without consulting
the manufacturer or the manufacturer s authorized supplier. Do not use backing pads that have a working speed of less
than the maximum rated speed of the tool's free speed. Any maintenance or repair work requiring the motor housing to
be opened may only be carried out by an authorized service center.
Battery and charger
The battery pack is not fully charged out of the carton. First read the safety instructions and then charge your battery
according to the instructions.
For optimal charging capacity the battery should be charged at an ambient temperature between 18 °C (64 °F) and 24
°C (75 °F). To prevent damage to the battery pack, do not charge the battery pack where the air temperature is below
4 °C (32°F) or above 40 °C (104 °F).
To obtain the longest possible battery life, we suggest the following:
Store and charge your battery in a cool area. Temperatures above or below normal room temperature will shorten
battery life.
Never store the battery in a discharged condition. Recharge it immediately after it has been discharged.
All batteries gradually lose their charge. The higher the temperature, the quicker they lose their charge.
If you store your tool for long periods of time without use, recharge the battery every month. This practice will prolong
battery life.
Charging procedure
Connect the power cord to the charger, and then plug into an outlet before inserting battery pack. All three charging
lights will be on for two seconds and then turn off.
Insert the battery pack into the charger. The lights will start to flash within 30 seconds.
During the charging process, the charging lights will indicate the status as follows:
Three charging lights will flash in sequence during the charging process.
Fully charged, all three lights will remain on continuously.
The charging process will last approximately 50 minutes for BPA 10825/11125 and 100 minutes for BPA 10850/11150
battery pack.
64
Mirka® AOS-B 130 & AROS-B 150
AOS-B 130
)
61.2 dB(A)
pA
)
72.2 dB(A)
3.0 dB(A)
*
2
2.54 m/s
h
2
1.5 m/s
PA
AROS-B 150
61.6 dB(A)
72.6 dB(A)
3.0 dB(A)
2
1.9 m/s
2
1.5 m/s

Publicité

loading

Ce manuel est également adapté pour:

Aros-b 150