Publicité
Les langues disponibles
Les langues disponibles
Parameter
Motors
OP. FORCE
CLS. FORCE
swc pressure
force
SUB BT
ELI BT A35 V
OP SPEED
All others
SUB BT
ELI BT A35 V
CL SPEED
All others
SUB BT
ELI BT A35 V
ELI BT A35 V + FCE
SLOW SPEED
PHOBOS VELOCE BT B35
All others
aintenance
(*) In the European Union, apply standard EN 12453 for force limitations.
(**) Impact forces can be reduced by using deformable edges.
TABLE "B" - LOGIC MENU - (logic)
Logic
Definition
Motor type
(Set the type of motor
OTOR TYPE
connected to the
Automatic Closure
TCA
INSTALLATION MANUAL
min.
max.
Default
1
100
50
1
100
50
0
100
100
20
100
20
100
100
15
100
20
100
20
100
100
15
100
20
50
20
50
20
50
25
15
50
15
100
0
250
Cross out
Default
setting
used
0
1
2
3
4
5
6
7
8
0
9
board).
10
11
12
13
14
15
16
17
0
1
0
2
Personal
Definition
Leaf force during opening
[%]
Leaf force during closing [%]
Leaf pressure force on the
closure limit-switch [%]
Opening speed [%}
Closing speed [%]
Slow-down speed [%]
Programming number of
operations for maintenance
0
threshold
[in hundreds]
Motors not active
NOT MANAGED
NOT MANAGED
IGEA BT
NOT MANAGED
NOT MANAGED
SUB BT
KUSTOS BT A - PHOBOS BT A - PHOBOS N BT
GIUNO ULTRA BT A 20 - GIUNO ULTRA BT A50
VIRGO SMART BT A - 5 wires
VIRGO SMART BT A - 3 wires
E5 BT A18
E5 BT A12
ELI BT A40 + FCE
ELI BT A35 V + FCE
ELI BT A40
ELI BT A35
PHOBOS VELOCE BT B35
Logic not enabled
Switches automatic closing on
It activates automatic closure also after a reversal due to an obstacle when closing. In case of a reversal
during opening, it retries opening after 2 seconds; if it finds an obstacle during opening 4 consecutive
times, it closes.
Configuration can only be activated with the E5 BT A12 motor (motor type 12).
The logic can only be used with pedestrian doors the energy of which is limited to within 1.69J.
Description
Force exerted by leaf/leaves during opening. This is
the percentage of force delivered, beyond the force
stored during the autoset cycle (and subsequently
updated), before an obstacle alarm is generated.
The parameter is set automatically by the autoset
function.
WARNING:
It
affects
directly: make sure that current safety
requirements are met with the set value
(*). Install anti-crush safety devices where
necessary (**).
Force exerted by leaf/leaves during closing. This is
the percentage of force delivered, beyond the force
stored during the autoset cycle (and subsequently
updated), before an obstacle alarm is generated.
The parameter is set automatically by the autoset
function.
WARNING:
It affects impact force
directly: make sure that current safety
requirements are met with the set value
(*). Install anti-crush safety devices where
necessary (**).
The force exerted by the leaf during the pressure
on the closure limit-switch.
Percentage of maximum speed that can be reached
by motor(s) during opening. WARNING: Once
the parameter has been edited, a complete
uninterrupted opening-closing cycle is required.
WARNING: when the display reads "SET", obstacle
detection is not active.
Percentage of maximum speed that can be reached
by motor(s) during closing. WARNING: Once
the parameter has been edited, a complete
uninterrupted opening-closing cycle is required.
WARNING: when the display reads "SET", obstacle
detection is not active.
Opening and closing speed of motor(s) during slow-
down stage, given as a percentage of maximum running
speed. WARNING: Once the parameter has been
edited, a complete uninterrupted opening-closing
cycle is required. WARNING: When the display reads
""SET"", obstacle detection is not active.
ATTENTION: for motor type ELI BT A35 it is not
possible to exclude the deceleration; values
greater than 50% will be considered at 50%.
Allows you to set a number of operations after
which the need for maintenance will be reported
on the AUX output configured as Maintenance or
Flashing Light and Maintenance .
Optional extras
THALIA BT A80 / BT A160 -
impact
force
51
Publicité
