Installation Instructions; Manufacturer's Terms Of Warranty; Scope Of Delivery; Installation Accessories - Truma Aventa comfort Mode D'emploi

Manufacturer's terms of warranty

1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults.
In addition to this, the statutory warranty claims against the
seller remain valid.
A claim under warranty shall not pertain:
– for parts subject to wear and in cases of natural wear and
tear,
– as a result of using components in the units that are not
original Truma parts in the units,
– as a consequence of failure to respect Truma instructions
for installation and use,
– as a consequence of improper handling,
– as a consequence of improper transport packing.
2. Scope of warranty
The warranty is valid for malfunctions as stated under item 1,
which occur within 24 months after conclusion of the pur-
chase agreement between the seller and the final consumer.
The manufacturers will make good such defects by subse-
quent fulfilment, i.e. at their discretion either by repair or
replacement. In the event of manufacturers providing service
under warranty, the term of the warranty shall not recom-
mence anew with regard to the repaired or replaced parts;
rather, the old warranty period shall continue to run. More ex-
tensive claims, in particular claims for compensatory damages
by purchasers or third parties, shall be excluded. This does not
affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. The warranty does not cover customer service work
in other countries.
Additional costs based on complicated removal and installa-
tion conditions of the appliance (e.g. removal of furniture or
parts of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG,
Wernher-von-Braun-Straße 12,
85640 Putzbrunn.
In Germany, always notify the Truma Service Centre if prob-
lems are encountered; in other countries the relevant service
partners should be contacted (see Truma Service Booklet or
www.truma.com). Any complaints are to be described in de-
tail. Please also specify the device serial number and date of
purchase.
To avoid transport damage, the device may only be dispatched
after agreement with the Truma Service Centre in Germany or
with the particular service partner concerned abroad. The risk
for possible transport damage will otherwise be borne by the
consignor.
If it is a case of warranty, the factory shall bear the cost for
the delivery to the factory and the cost for returning the ap-
pliance to the customer. If the damage is deemed not to be
a warranty case, the manufacturer shall notify the customer
and shall specify repair costs which shall not be borne by the
manufacturer; in this case, the customer shall also bear the
shipping costs.
20

Installation instructions

Installation and repair of the device may only be carried out by
properly qualified professionals. Before staring work, read the
installation instructions thoroughly and follow them carefully!

Scope of delivery

External unit:
– 1 Aventa comfort
– 2 brackets
– 4 screws, M6 x 70, coated with sealant
– 6 screws, M6 x 12, coated with sealant
– 1 base ring
– 2 roof thickness adapters (each 10 mm)
– 1 remote control with mounting
– 2 screws, 2.9 x 16 for mounting
– 2 batteries, type AAA
– 1 set of instructions for installation and use
– 1 installation template
– 3 Wago terminals
Air distributor:
– 1 air distributor, fully assembled

Installation accessories

10 mm roof thickness adapter, 1 x (part no. 40091-16900)
Sealing frame (part no. 40091-19500)
recommended for optimum sealing in the case of retrofitting
in vehicles with cut-outs measuring 400 x 400 mm.
Covering tape
Cream (part no. 40091-31200)
Grey (part no. 40091-31300)
for covering gaps of up to 5 mm between the air distributor
and the roof.
l ~ 2,36 m

Intended use

This unit was designed for installing in motor homes and cara-
vans. It is intended for domestic use. Any other applications
are only possible after consultation with Truma.