Einstellungen Schalter S1; Fußschalter-Betrieb; Settings Of Switch S1; Operation Via Foot Switch - Ismatec VC-280/1 Mode D'emploi

Table des Matières

Publicité

DIP-Switch
z1 2 3 4 5 6
o
Das Gerät darf nur von einer Fach-
kraft geöffnet werden!
Spannungsführende Teile im Innern des
Gerätes können auch längere Zeit nach
Ziehen des Netzsteckers noch unter Span-
nung stehen.
The instrument should only be
opened by a qualifi ed technician!
Capacitors inside the pump may still be
charged even though the mains plug has
been disconnected some time ago.
Cet appareil ne peut être ouvert que
par un spécialiste!
Des pièces conductrices peuvent encore
être sous tension très longtemps après
que le câble ait été débranché de la prise.
ISMATEC SA/ecoline/17.11.05/CB/GP/TM

Einstellungen Schalter S1

i P
s n
m I
. p
kΩ
– 0
V 5
1
0 0
kΩ
0
1 –
V 0
2
P
n i
5
s
e p
d e
N I
kΩ
– 0
0 2
m
A
2
0 4
kΩ
– 4
0 2
m
A
2
0 4
* Default-Einstellung
k Vergewissern Sie sich, dass die
Pumpe vom Netz getrennt ist.
Um an die Schalter zu gelangen,
seitlich 4 Schrauben lösen und Ge-
häuse nach oben abheben (auf Kabel
achten).
Fußschalter-Betrieb
Mit DIP-Switch 4 kann zwischen zwei
Möglichkeiten gewählt werden:
Dip-Switch 4 off = Ein/Aus
Dip-Switch 4 on = ein, solange Fuß-
schalter gedrückt bleibt.

Settings of switch S1

D
P I
S -
w
t i
h c
1
D
P I
S -
w
t i
h c
2
D
P I
S -
F O
* F
F O
* F
F O
* F
O
F F
O
N
O
F F
O
N
O
F F
O
F F
O
N
O
F F
O
N
* Default setting
k Check that the pump is discon-
nected from the mains.
For reaching the DIP-switch you
need to unscrew the 4 screws on
both sides of the pump. Then, lift the
housing carefully (mind the cables)
and remove it.
Operation via foot-switch
With DIP switch 4 the user can switch
between two possibilities:
Dip-Switch 4 off = On/Off
Dip-Switch 4 on = on, as long as
pressure is maintained on the foot-
switch.
Réglages du switch S1
w
t i
h c
3
D
P I
S -
w
t i
h c
4
D
P I
S -
w
t i
h c
F O
* F
F O
* F
O
F F
O
F F
O
F F
O
F F
O
F F
O
F F
* Valeurs par défaut
k Assurez-vous que la pompe est
déconnectée du réseau.
Pour accéder aux interrupteurs, dé-
visser les 4 vis latérales et soulevez le
boîtier (faites attention aux câbles).
Utilisation avec pédale de com-
mande
Avec le DIP switch 4, l'utilisateur peut
choisir entre deux possibilités:
Dip-Switch 4 off = Marche/Arrèt
Dip-Switch 4 on = marche, aussi
longtemps que la pédale de com-
mande reste enfoncée.
5
D
P I
S -
w
t i
h c
6
F O
* F
O
F F
O
F F
O
F F
29

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Vc-360Vc-380/1Vc-easy-loadVc-ms/ca8-6Vc-ms/ca4-12

Table des Matières