Cleaning And Maintenance - Bard EnCor ENSPIRE Mode D'emploi

After Use
12. Remove disposables and discard per your facility's procedures. Clean and
disinfect the system hardware per the instructions located under the cleaning and
maintenance section.
Note: The system may be left on if additional procedures are to be performed;
it is not recommended to leave the main power on overnight. It is not
recommended to unplug the drivers after each use. The drivers and foot pedal
may be left connected to the E
procedures are to be performed with the same drivers.
13. To set the system to standby, press and hold the switch on the front of the console
(illustrated in Figure 13) until the system shuts down. To turn off the main power,
press the main switch located on the rear of the console (illustrated in Figure 12).
I. CLEANING AND MAINTENANCE
To clean the E C E Breast Biopsy System, turn off power and disconnect the power cord from the AC outlet. Leave all other cables connected. Clean
N OR NSPIRE TM
C
N
cleaning solution or disinfectant. Follow the procedures approved by your facility or use a validated infection control procedure. Always follow the instructions
provided by the manufacturer of the cleaner or disinfectant used.
it to malfunction and will void the warranty.
Do not submerge any component of the E
cause the system to malfunction and will void the warranty. Do not autoclave any components of the E
over 54°C (129°F).
Disposal of Equipment
After following the cleaning recommendations above, there are no biohazard risks involved with the disposal of the E
any of the reusable accessories at the end of the E
Do not dispose of the E C E
N OR NSPIRE
Routine Maintenance
No calibrations or adjustments are necessary for the E
of normal use. In addition, the following routine maintenance activities may be completed:
Electrical safety testing should be performed at intervals no greater than 12 months, using a standard
medical safety analyzer.
Regularly inspect all cables and connectors for possible wear or damage.
Odor Control Filter Replacement
Turn the Power Switch to off at the rear of the console. Remove the old Odor Control Filter by rotating
it counter-clockwise and discard. Install the new Odor Control Filter (F3000) by rotating clockwise until
Fuse Replacement
The fuse holder is accessible after the power cord is removed. Unplug the E
Biopsy System from the wall outlet, and remove the power cord from the power inlet connector on
the rear panel of the console. Using a small slotted screwdriver, press the release tab located near
the center of the fuse holder. Pull the fuse holder assembly outward to remove it. Use Fuse Kit
Model Number FK4000. Install the fuse holder, as illustrated in Figure 19. Remove and replace any
blown fuses in the fuse holder assembly, and snap it back into place. The fuse holder orientation
determines the voltage. Figure 19 illustrates the 115V orientation. Rotate the fuse 180 degrees for
230V orientation. Replace the fuse holder assembly, and reconnect the power cord to the power inlet
connector.
J. TROUBLESHOOTING
The E C E TM Breast Biopsy System is programmed to attempt to determine a reason for any alert condition that occurs. If the system can identify the cause of the alert,
N OR NSPIRE
the information is displayed on the touch screen.
Depending on the cause of the alert, different actions may be required to clear the alert. Certain alert conditions, when corrected, allow the system to recover automatically, and
Use for that driver to clear the alert.
turn the main power back on, and restart the E
If any alert condition persists after correcting known problems and clearing the alert condition from the screen, contact Bard for service.
Marker Mode tab
TM
C E Breast Biopsy system if all
N OR NSPIRE
E Breast Biopsy System, cables, and foot pedal with a soft, lint-free cloth dampened with Dispatch or a similar
OR NSPIRE TM
C E
N OR NSPIRE TM
C E
N OR NSPIRE
TM Breast Biopsy System by placing into trash receptacles.
C E
N OR NSPIRE
Figure 18.
C E Breast Biopsy System with the standby button on the front of the console (illustrated in Figure 13).
N OR NSPIRE TM
180° button
TM
C E Breast Biopsy System or cables. Spraying the system may cause
N OR NSPIRE
TM
TM Breast Biopsy System outside
C E TM Breast
N OR NSPIRE
4
Figure 17 – The touch screen – Marker Mode
C E Breast Biopsy System. Do not heat
N OR NSPIRE TM
C E TM Breast Biopsy System or
N OR NSPIRE
Figure 18 – Odor Control Filter
Figure 19 – Replacement Fuse Orientation:
Orientation for 115V shown
Figure 12