Work Area; Personal Protective Equipment - Hilti TE 805 Mode D'emploi

c) Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may con-
tact hidden wiring or its own cord. Cut-
ting accessory contacting a "live" wire may
make exposed metal parts of the power tool
"live" and could give the operator an elec-
tric shock.
d) Always hold the tool securely, with both
hands on the grips provided. Keep the
tool, especially its grip surfaces, clean
and free from oil and grease.
e) Breathing protection must be worn when
the tool is used without a dust removal
system.
f) Exercise your fingers during pauses
between work to improve the blood cir-
culation in your fingers.
g) To avoid tripping and falling when work-
ing, always lead the sypply cord, exten-
sion cord and dust extraction hose away
tho the rear.
h) The tool is not intended for use by chil-
dren, by debilitated persons or those
who have received no instruction or
training.
i) Children must be instructed not to play
with the tool.
j) Dust from material such as paint con-
taining lead, some wood species, miner-
als and metal may be harmful. Contact
with or inhalation of the dust may cause
allergic reactions and/or respiratory dis-
eases to the operator or bystanders. Cer-
tain kinds of dust are classified as car-
cinogenic such as oak and beech dust
especially in conjunction with additives
for wood conditioning (chromate, wood
preservative). Material containing
8
Printed: 08.07.2013 | Doc-Nr: PUB / 5071241 / 000 / 01
asbestos must only be treated by spe-
cialists. Where the use of a dust extrac-
tion device is possible it shall be used.
To achieve a high level of dust collec-
tion, use a suitable vacuum cleaner of
the type recommended by Hilti for wood
dust and/or mineral dust together with
this tool. Ensure that the workplace is
well ventilated. The use of a dust mask
of filter class P2 is recommended. Fol-
low national requirements for the mate-
rials you want to work with.
2.2 Electrical safety
a) Before beginning work, check the work-
ing area (e.g. with a metal detector) to
ensure that no concealed electric
cables or gas and water pipes are pre-
sent. External metal parts of the tool may
become live if, for example, an electric
cable is damaged inadvertenly. This pre-
sents a serious risk of electric shock.
b) Check the condition of the supply cord
and its plug connections and have it
replaced by a qualified electrician if
damage is found. Check the condition
of the extension cord and replace it if
damage is found. Do not touch the sup-
ply in the event of it suffering damage
while working. Disconnect the supply
cord plug from the socket. Damaged
supply cords and extension cords pre-
sent a risk of electric shock.
c) Dirty or dusty electric tools should thus
be checked at a Hilti service center at
regular intervals, especially if used fre-
quently for working on conductive mate-
rials. Dust (especially dust from con-
ductive materials) or dampness adhering
to the surface of the tool may, under unfa-
vorable conditions, present a risk of elec-
tric shock.
2.3 Power tool use and care
a) Ensure that the insert tools used are
equipped with the appropriate connec-
tion end system and that they are prop-
erly fitted and secured in the chuck.
b) In the event of a power faillure, switch
the tool off and unplug the supply cord.
This prevents inadvertent starting when
the power returns.

2.4 Work area

a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ven-
tilated. Poorly ventilated workplaces
may be injurious to the health due to
exposeure to dust.

2.5 Personal protective equipment

The user and any other persons in the
vicinity must wear suitable eye protection,
a hard hat, ear protection and protective
gloves when the tool is in use. Breathing
protection must be worn if no dust removal
system is used.
Wear eye
Wear a
protection hard hat protection
Wear Wear
protective breathing
gloves protection
The general safety precautions for power
tools contain all product-specific precau-
tions for the power tool described in these
operating instructions. The precautions
listed under (1.3 c, d, f, g) are not relevant
to this power tool.
Wear ear