Table des Matières
Publicité
no display
(horizontal louvers
stops at current position)
When selecting "
●
air automatically. Horizontal louver will automat-
ically swing up & down at maximum angle.
●
When selecting
er is blowing air at fixed position. Horizontal
louver will stop at the fixed position.
●
When selecting "
blowing air at fixed angle. Horizontal louver will
send air at the fixed angle.
Hold "
"button above 2s to set your required
●
swing angle. When reaching your required
angle, release the button.
NOTE
●
"
" may not be available. When air condi-
、
、
tioner receives this signal, the air conditioner will blow
fan automatically.
button
CLOCK
Press this button to set clock time. "
remote controller will blink. Press "+" or "-" button
within 5s to set clock time. Each pressing of "+" or
"-" button, clock time will increase or decrease 1
minute. If hold "+" or "-" button, 2s later, time will
change quickly. Release this button when reaching
your required time. Press "CLOCK" button to
confirm the time. "
NOTE
●
Clock time adopts 24-hour mode.
The interval between two operations can
●
Otherwise, remote controller will quit setting status.
Operation for TIMER ON/TIMER OFF is the same.
/
TIMER ON
TIMER OFF
●
TIMER ON button
"TIMER ON" button can set the time for timer
on. After pressing this button, "
pears and the word "ON" on remote controller
blinks. Press "+" or "-" button to adjust TIMER
ON setting. After each pressing"+" or "-" button.
TIMER ON setting will increase or decrease
1min. Holding "+" or "-" button, 2s later, the time
will change quickly until reaching your required
time.
", air conditioner is blowing
air condition-
、 、
", air conditioner is
、
、
" icon on
" icon stops blinking.
'
t exceed 5s.
button
" icon disap-
Press "TIMER ON" to confirm it. The word "ON"
will stop blinking. "
Cancel TIMER ON: Under the condition that
TIMER ON is started up, press "TIMER ON"
button to cancel it.
●
TIMER OFF button
"TIMER OFF" button can set the time for timer
off. After pressing this button, "
pears and the word "OFF" on remote controller
blinks. Press Press "+" or "-" button to adjust
TIMER OFF setting. After each pressing "+" or
"-" button, TIMER OFF setting will increase or
decrease 1min. Holding "+" or "-" button, 2s
later, the time will change quickly until reaching
your required time.
Press "TIMER OFF" and the word "OFF" will
stop blinking. "
Under the condition that TIMER OFF is started
up, press "TIMER OFF" button to cancel it.
NOTE
●
Under on and off status, you can set TIMER OFF or
TIMER ON simultaneously.
●
Before setting TIMER ON or TIMER OFF, please
adjust the clock time.
●
After starting up TIMER ON or TIMER OFF, set the
constant circulating valid. After that, air conditioner
will be turned on or turned off according to setting
time. ON/OFF button has no effect on setting. If you
don 't need this function, please use remote control-
ler to cancel it.
button
X-FAN
Press this button under cool and dry mode to start
up X-FAN function, and "
ler will be displayed. Press this button again to
cancel X-FAN function, and "
NOTE
●
When X-FAN function is on, if the air conditioner is
turned off, indoor fan will still operate at low speed
for a while to blow the residual water inside the air
duct.
●
During X-FAN operation, press X-FAN button to turn
off X-FAN function. Indoor fan will stop operation
immediately.
button
TURBO
Under cool or heat mode, press this button to turn
to quick cool or quick heat mode. "
displayed on remote controller. Press this button
9
" icon resumes displaying.
"icon disap-
" icon resumes displaying.
" icon on remote control-
" icon will disappear.
" icon is
Publicité
Table des Matières
