Programming Keygo Io Remote Controls For Full And Partial Opening Operation; Programming Keytis Io Remote Controls For Full And Partial Opening Operation - SOMFY Dexxo Pro 800 io Manuel D'installation

Dexxo Pro io
Automatic closure time delay
Values 0 to 12 (time delay value = value x 10 s)
2: 20 s
Lighting time delay
Values 0 to 60 (time delay value = value x 10 s)
6 : 60 s
Comments Remark: Due to the thermal cut out protection system, the
integrated light may cut out automatically if it is used for an
extended length of time. We therefore recommend selecting
a light time delay in excess of 2 mn (t1=12 or 120s) only
when remote lighting is used.
> Programming example: setting the "P7" closure approach
speed (Fig. 39)
Setting up a long soft stop function zone "P7" = 2.
> Special case: adjusting the position of the door for partial
opening (Fig. 40)
Select setting "P6" and validate by pressing "OK".
Move the door to the desired partially open position:
- Pressing and holding the "-" button will close the door.
- Pressing and holding the "+" button will open the door.
- Validate by pressing "OK".
- Exit the menu with "SET".
> Forced mode (Fig. 41)
This function makes it possible to manipulate the door at any moment (loss of
remote control, photoelectric cell fault, etc.).
Door stationary:
- press the "-" button to close it
- press the "+" button to open it.
Door moving: press the "-" or "+" button to stop the door.
> Programming a Situo Telis Composio Impresario type remote
control (Fig. 42)
Before programming the remote control, make sure that it has already
memorised the system key. (Refer to the corresponding remote control
documentation).
[1]. Press the "PROG" button on Dexxo Pro until the light comes on.
[2]. Briefly press the "PROG" button on the remote control.
Wait for the Dexxo Pro light to blink.
This may take from a few seconds to around a minute depending on the
number of products connected to the system.
Remark: Dexxo Pro can memorise up to 9 Situo remote controls. For other
types of remote controls, no limit applies.
8 - PROGRAMMING KEYGO IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
In order for the garage door to open fully and partially, parameter P4 must be
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
previously programmed during commissioning become programmed
buttons to partially open the garage door.
An additional memorising command must be performed on buttons
which are used to fully open the garage door.
The operations to be performed differ according to the desired function for
the button being programmed (full or partial opening), and depending on
the memorisation which has already been performed on the button prior to
activation of parameter P4.
> Switch to full opening for a button previously memorised
during commissioning (Fig.43)
[1]. Simultaneously press the large button and the left-hand outer button on
the remote control.
Copyright © 2015 SOMFY ACTIVITES SA. All rights reserved
The remote control indicator light flashes.
[2]. Press the remote control button previously memorised during
commissioning within 10 seconds.
The button for full opening has been memorised.
> Memorise a button that has not yet been programmed to
trigger partial opening (Fig.23)
[1]. Press the "PROG" button on the Dexxo Pro until the light comes on (2
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
The remote control indicator light flashes.
[3]. Briefly press the selected button to partially open the Dexxo Pro motor.
The light of the Dexxo Pro motor flashes for 5 seconds.
The button for partial opening has been saved.
> Memorise a button that has not yet been programmed to
trigger full opening (Fig. 44)
[1]. Press the "PROG" button on the Dexxo Pro until the light comes on (2
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
The remote control indicator light flashes.
[3]. Briefly press the selected button to operate the Dexxo Pro motor for full
opening.
The light of the Dexxo Pro motor flashes for 5 seconds.
[4]. Simultaneously press the large button and the left-hand outer button on
the remote control.
The remote control indicator light flashes.
[5]. Press the remote control button that you wish to use for full opening within
10 seconds.
The button for full opening has been memorised.
9 - PROGRAMMING KEYTIS IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
In order for the garage door to open fully and partially, parameter P4 must be
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
previously saved during commissioning are programmed to fully
open the garage door. An additional command must be performed
on buttons which are used to partially open the garage door.
> Save a button that has not yet been programmed to trigger
partial opening (Fig.45)
[1]. Save the button on the Dexxo Pro (refer to the section on "Programming
using the Dexxo Pro motor", on page 6).
[2]. Simultaneously press the saved button and the "STOP" button on the
remote control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch to partial opening for a button previously saved during
commissioning (Fig. 46)
Simultaneously press the saved button and the "STOP" button on the remote
control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch a button previously programmed for partial opening to
full opening (Fig. 47)
Simultaneously press the saved button and the "STOP" button on the remote
control.
The remote control beeps 3 times.
The button for full opening has been programmed.
> To determine the operating mode in which a button is
programmed
When the saved button and the "STOP" button on the remote control are
simultaneously pressed, if the remote control:
10