Programming Keygo Remote Controls - Fig. 23 And; Operating Test; Using Keytis Remote Controls - Fig; Using Keygo Remote Controls - Fig - SOMFY Dexxo Pro 800 io Manuel D'installation

Dexxo Pro io
It is impossible to program Keytis remote controls in the following
cases:
- The remote control has not memorised the system key.
- A number of installation receivers are in programming mode.
- A number of remote controls are in key transfer or programming
modes.
Any incorrect programming is indicated by a series of fast beeps
together with the orange indicator blinking on the Keytis remote
control.
At this stage in the installation process, the Dexxo Pro motor drive unit
is ready to run.

4.7 Programming Keygo remote controls - Fig. 23 and

24
Each control button is programmed individually.
To clear a previously programmed button, refer to the section entitled "Clearing
Keygo remote controls".
There are two ways to program the remote control:
- Programming from a Dexxo Pro motor.
- Programming by copying a previously programmed Keygo io remote
control.
> Programming from a Dexxo Pro motor (Fig. 23)
[1]. Press the "PROG" button on the Dexxo Pro until the light comes on (2
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
The remote control indicator light flashes.
[3]. Briefly press the selected button to actuate the Dexxo Pro motor.
The light of the Dexxo Pro motor flashes for 5 seconds.
> Programming by copying a previously programmed Keygo io
remote control (Fig. 24)
This operation is used to copy the programming of a previously programmed
remote control button.
[1]. Simultaneously press the outer right and outer left buttons on the
previously programmed remote control (A) until the green indicator light
comes on.
[2]. Press the button for 2 seconds to copy the previously programmed remote
control (A).
[3]. Simultaneously briefly press the outer right and outer left buttons on the
new remote control (B).
[4]. Briefly press the selected button to actuate the Dexxo Pro on the new
remote control (B).
At this stage in the installation process, the Dexxo Pro motor drive unit
is ready to run.

5 - OPERATING TEST

5.1 Using Keytis remote controls - Fig. 25

5.2 Using Keygo remote controls - Fig. 26

5.3 Obstacle detection function - Fig. 27 and 28

The detection of an obstacle during door opening will stop the door (Fig. 27).
The detection of an obstacle during door closure will reopen the door (Fig. 28).
Make sure that obstacle detection works when the door encounters an obstacle
50 mm from the ground.

5.4 Built in lighting operation

The light will come on every time the motor drive unit is operated. It will go
out automatically after one minute once the door stops. This time delay is
adjustable (refer to the Setup chapter). Repetitive use which causes the light to
stay on continually may result in an automatic cut-off condition triggered by the
thermal cut out protection mechanism.

5.5 End-users training

The end-users must be imperatively instruct to the safety use of this motorised
door (standard use and manual release principle) as well as to periodic and
compulsery checks.
Copyright © 2015 SOMFY ACTIVITES SA. All rights reserved

6 - CONNECTING PERIPHERALS

6.1 Description of the various peripherals - Fig. 29

Key. Description
1 Orange light
2 Remote lighting
3 Code keypad
4 Keyswitch
5 Aerial
6 Battery
7 Pedestrian door safety kit
8 Photoelectric cells
9 Reflex type cells
10 Sensor bar
6.2 Electrical connections for the various peripherals -
Fig. 29 to 38
Cut the electric power supply to the motor before performing any work on
peripherals. If the display remains off after working on the system, check the
wiring (for possible short circuits or polarity reversals).
> General electrical diagram (Fig. 29)
> Photoelectric cells (Fig. 30)
It is compulsory to install photoelectric cells:
- If automatic closing is activated (P0=1)
- If the automatic function is controlled remotely (not visible to the
user)
Two types of connections can be made:
A : Standard (without self test): program the setting "P2" = 2.
B : With self test: program the setting "P2" = 1.
This means that an automatic test is conducted to check photoelectric
cell operation every time the door operates.
If the test fails, no door movement is possible.
> Reflex photoelectric cell (Fig. 31)
With self test: program the setting "P2" = 1.
This means that an automatic test is conducted to check photoelectric cell
operation every time the door moves.
If the test fails, no door movement is possible.
> Sensor bar (Fig. 32)
With self test: program the setting "P2" = 1.
This is used to perform an automatic test of sensor bar operation every time
the door moves.
If the test result is negative, no door movement is possible.
Make sure you have correctly configured parameter "P2" taking into
account the photoelectric cells or the sensor bar.
> Orange light (Fig. 33)
Program the setting "P1" depending on the required operating mode:
- Without warning before door movement: "P1" = 0.
- With a 2 s warning before door movement: "P1" = 1.
> Code keypad (Fig. 34)
> Pedestrian door safety kit (Fig. 35)
When the pedestrian door contact is fitted, it must be connected in place of the
jumper normally fitted between terminals 5 and 6.
If the pedestrian door contact is removed, the jumper between
terminals 5 and 6.
> Battery (Fig. 36)
> Aerial (Fig. 37)
8