Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Page 10 of 23
•
Secure the wiring and connectors by using the cable ties (item 17) to keep the wires together
and use the cable tie slots provided on the underside of the cover plate to secure the wires
neatly.
•
Push the opposite end of the loom through the rubber bung in the main bracket (item 1) and
pull through the extra wire.
•
Use the self-adhesive cable clips (item 18) to tidy any loose wires.
•
The tail tidy is now fully assembled and can be affixed to the bike, offer the tail tidy up to the
bike as shown in picture 21. Ensure the spacers fitted earlier protruding through the tail unit of
the bike sit into the slotted mounts on the main bracket (item 1).
•
Using the M6 x 25 bolt (item 6) and one M6x12mm washer (item 8) in the rearward hole on
the mounting tab slot, secure the tail tidy loosely into place.
•
From below, pass the M6x20mm bolts (item 7) through the main bracket (item 1) and
spacers, so the end of the bolt is accessible from the inside of the bike.
•
Secure these bolts in place by using one M6x19mm washer (item 9) and an M6 Nyloc nut
(item 10) for each bolt.
•
Adjust the tail tidy on the slots if necessary, to ensure all components line up correctly
•
Now fully tighten each bolt to the correct torque so the tail tidy is fully secured to the bike.
•
Reconnect the OEM sub-loom to the OEM connector removed previously.
•
Test both indicators and the licence plate light function correctly. If lights fail to illuminate, then
swap the bullet connectors around and re-test.
•
Re-fit the bodywork as previously fitted by reversing the steps above.
•
Re-fit the licence plate (it may require drilling).
•
Depending on local laws, attach enclosed reflector (item 19) in an appropriate location.
•
Test the licence plate illuminator and all lights before riding.
•
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON
THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE
HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE
ROAD. IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE
AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.
Unit
Tel: +44 (0)
420 89007 Fax: +44 (0)
1
ISSUE 1
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 87301 www.rg-racing.com Email: info@rg-racing.com
1
17/03/2021
(DM)
R&G
LP0299
Publicité
Table des Matières
