Technical Data; Preparations For Use - Roller Arco Notice D'utilisation

eng ROLLER'S Arco / ROLLER'S Arco 50 / ROLLER'S Akku-Arco
1. Technical Data
Use for the intended purpose
WARNING
ROLLER'S Arco and ROLLER'S Akku-Arco are intended for the purpose of cold
draw bending of pipes up to 180°.
ROLLER'S Arco 50 is intended for cold draw bending of pipes up to 90°.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
ROLLER'S Arco: Electric pipe bending machine, insert bolts, bending
formers and back formers according to ordered set,
instruction manual, steel case.
ROLLER'S Arco 50: Electric pipe bending machine, square driver 35 – 50,
support 35 – 50, insert bolt, instruction manual,
transport crate.
ROLLER'S Akku-Arco: Cordless pipe bending machine, Li-Ion battery, rapid
charger Li-Ion/Ni-Cd, insert bolt, bending formers and
back formers according to ordered set, instruction
manual, steel case.
1.2. Article numbers
ROLLER'S Arco drive unit
ROLLER'S Arco 50 drive unit
ROLLER'S Akku-Arco Li-Ion drive unit
Square driver 35 – 50, support 35 – 50
Square driver 10 – 40, support 10 – 40
Insert bolt
Rapid charger Li-Ion/Ni-Cd
Li-Ion 18 V, 3.2 Ah battery
ROLLER'S bending spray, 400 ml
Machine holder 3B
Machine holder WB
Steel case (ROLLER'S Arco)
Steel case (ROLLER'S Akku-Arco)
Transport crate (ROLLER'S Arco 50)
Steel case (bending former and back former of ROLLER'S Arco 50) 586012
Machine cleaner
Bending formers and back formers
1.3. Applications
No cracks or wrinkles shall occur during professional cold bending. Pipe
qualities and sizes which do not guarantee this are not suited to be bent with
ROLLER'S Arco, ROLLER'S Arco 50 and ROLLER'S Akku-Arco.
Hard copper pipes are cold bendable up to Ø 18 mm according to DIN EN
1057, minimum radii must be complied with. Bending formers and back formers
for larger bending radii can be supplied.
ROLLER'S Arco
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 35 mm, Ø ⅜ –1⅜".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Stainless steel pipes of the pressfitting systems Ø 12 – 28 mm.
● Jacketed C-steel pipes of the pressfitting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼" – ¾".
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
● Composite pipes Ø 14 – 40 mm.
Largest bending angle
ROLLER'S Arco 50
● Steel pipes as per DIN EN 10255 (DIN 2440) Ø ¼" – 1¼".
● Hard, half-hard and soft copper tubes Ø 10 – 42 mm.
● Thin walled copper tubes Ø 10 – 35 mm.
● Stainless steel tubes of pressfitting systems Ø 12 – 42 mm.
● (Jacketed) C-steel pipes of the pressfitting systems Ø 12 – 35 (28) mm.
● Composite tubes Ø 14 – 50 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Electrical installation pipes DIN EN 50086 Ø 16 – 32 mm.
Largest bending angle
ROLLER'S Akku-Arco
● Hard, half-hard, soft copper pipes, also thin walled, Ø 10 – 28 mm, Ø ⅜ – 1⅛".
● Soft, jacketed copper pipe, also thin walled, Ø 10 – 18 mm.
● Stainless steel pipes of the pressfitting systems Ø 12 – 28 mm.
● Jacketed C-steel pipes of the pressfitting systems Ø 12 – 28 mm.
● Soft precision steel pipes Ø 10 – 28 mm.
● Steel pipes DIN EN 10255 (DIN 2440) Ø ¼ – ½".
● Electrical installation pipes DIN EN 50086 Ø 16 – 25 mm.
● Composite pipes Ø 14 – 32 mm
Largest bending angle
1.4. Speed Arco
Speed infinitely
adjustable 0...4 min‫¹־‬
12
All manuals and user guides at all-guides.com
580000
580100
580002
582110
582120
582036
571560
565225
140120
586100
586150
586000
586015
590160
140119
see Fig. 3
180°
90°
180°
Arco 50 Akku-Arco
0...1 min‫ ¹־‬ 0...3,33 min‫¹־‬
1.5. Electrical data
ROLLER'S Arco, 230 V, 1~, 50 – 60 Hz; 1000 W; 4.8 A or
ROLLER'S Arco 50 110 V, 1~, 50 – 60 Hz; 1000 W; 9.6 A,
Intermittent service S3 15% 2/14 min,
double-insulated, interference-suppressed.
Protection class II. Protection class IP 20.
ROLLER'S Akku-Arco 18 V =
Rapid charger Input
Output
Input
Output
1.6. Dimensions (mm) Arco
L×W×H: 585×215×140
(23"×8½"×5½") (25"×9½"×3¾") (21¼"×11"×5½")
1.7. Weights
Drive unit 8.3 kg
(18.3 lb)
Bending former 0.2 ... 3.8 kg
(0.4 ... 8.4 lb)
Back former 0.1 ... 0.2 kg
(0.2 ... 0.4 lb)
Insert bolt 0.4 kg (0.9 lb)
ROLLER'S battery Li-Ion
18 V, 3.2 Ah
1.8. Noise information Arco
Emission at
workplace 93 dB (A)
Sound pressure level L
= 86 dB
pA
Sound power level L = 88 dB
wA
Uncertainty K = 3 dB
1.9. Vibrations
Weighted effective
value of acceleration 2.5 m/s²
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION
The indicated weighted effective value of acceleration can differ during opera-
tion from the indicated value, dependent on the manner in which the device is
used. Dependent upon the actual conditions of use (periodic duty) it may be
necessary to establish safety precautions for the protection of the operator.
2. Preparations for Use
2.1. Electrical connection
WARNING
Caution: Mains voltage present! Before connecting the electric pipe bending
machine or the rapid charger, check whether the voltage given on the rating
plate corresponds to the mains voltage. On building sites, in a wet environment,
indoors and outdoors or under similar installation conditions, only operate the
electric pipe bending machine on the mains with a fault current protected switch
(FI breaker) which interrupts the power supply as soon as the leakage current
to earth exceeds 30 mA for 200 ms.
Rechargeable batteries
NOTICE
Always hold the battery (17) upright when inserting it in the drive unit or the
rapid charger. If inserted at an angle it can cause damage to the contacts and
result in a short circuit which damages the battery.
Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by "total discharge". The cells of the ROLLER'S
Li-Ion battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion
batteries must be charged before use and recharged regularly. Failure to observe
this regulation of the cell manufacturer can lead to damage to the Li-Ion battery
by total discharging.
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to
total discharge damage of the battery after longer storage. Li-Ion batteries must
therefore be charged before storing and recharged every six months at the
latest and charged again before use.
NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
eng
230 V~; 50 – 60 Hz; 65 W,
Protection class II.
10.8 – 18 V =
100 – 120 V ~; 50 – 60 Hz; 65 W,
Protection class II.
10.8 – 18 V =
Arco 50 Akku-Arco
640×240×95 540×280×140
16.9 kg 8.6 kg (with batt.)
(37.3 lb) (19.0 lb)
4.44 ... 7.8 kg 0,2 ... 2.6 kg
(9.7 ... 17.2 lb) (0.4 ... 5.7 lb)
0.2 ... 0.4 kg 0.1 ... 0.2 kg
(0.4 ... 0.9 lb) (0.2 ... 0.4 lb)
0.4 kg (0.9 lb) 0.4 kg (0.9 lb)
0.7 kg (1.5 lb)
Arco 50 Akku-Arco
92 dB (A) 81 dB (A)
88 dB 75 dB
88 dB 88 dB
2.5 m/s² 2.5 m/s²