Specific Safety Instructions; Technical Data - Roller Uni-Press E Instructions D'emploi

eng

Specific Safety Instructions

Use personal safety equipment (e.g. goggles).
•
Avoid unnatural postures, and do not lean too far forward.
•
Before changing the pressing or expanding tools, pull the mains plug or take
•
out the battery!
The drive units develop a very high pressing force. For that reason, be par-
•
ticularly careful. Keep all other persons away from the working area during
working.
Hold the drive units only by the housing grip and the pistol grip during ope-
•
ration. Keep your hands away from moving parts (pressing area, expan-
ding area)!
Never operate radial presses when the tongs shank (2) is not locked. Risk
•
of fracture!
Always position radial presses with the pressing tongs on the press fitting
•
at right angles to the pipe axis. Never position it askew.
Do not start radial presses without pressing tongs inserted. Do not start the
•
pressing operation except to make a press joint. Unless counter pressure
is applied by the press fitting, the drive unit or pressing tongs will be needlessly
stressed.
Before using pressing tongs from other manufacturers, check that they are
•
suitable for the drive unit. Consult and comply with the pressing tongs
manufacturers' instructions for use.
Only operate axial presses with pressing heads fully inserted. Risk of fracture!
•
Always position axial presses with the pressing tongs on the compression
•
sleeve fitting at right angles to the pipe axis. Never position it askew.
Screw expanding heads as far as they will go onto the expander.
•
Do not attempt to repair damaged pressing tongs, pressing heads or
•
expanding heads. Risk of fracture!
Consult and comply with the instructions for installation and fitting of the
•
system's manufacturers.

1. Technical Data

1.1. Article numbers
ROLLER'S Uni-Press E drive unit
ROLLER'S Uni-Press 2000 drive unit
ROLLER'S Uni-Press ACC drive unit
ROLLER'S Multi-Press Mini ACC drive unit
ROLLER'S Multi-Press drive unit
ROLLER'S Multi-Press ACC drive unit
ROLLER'S Axial-Press 5 drive unit
ROLLER'S Axial-Press 15 drive unit
ROLLER'S Axial-Press 40 drive unit
ROLLER'S Akku-Exparo Mini Q & E drive unit
ROLLER'S Akku-Exparo Q & E drive unit
ROLLER'S battery 12 V, 1,3 Ah
ROLLER'S battery 12 V, 2,0 Ah
ROLLER'S voltage supply 230 V
Rapid charger 12–18 V
Sheet steel case, ROLLER'S Uni-Press E
Sheet steel case, ROLLER'S Uni-Press 2000
Sheet steel case, ROLLER'S Uni-Press ACC
Sheet steel case, ROLLER'S Multi-Press
Sheet steel case, ROLLER'S Axial-Press 5
Sheet steel case, ROLLER'S Axial-Press 15 and 40
Sheet steel case, ROLLER'S Multi-Press Mini ACC,
ROLLER'S Akku-Exparo Mini Q & E
Sheet steel case, ROLLER'S Akku-Exparo Q & E
1.2. Capacity
ROLLER'S Multi-Press Mini ACC
Radial press for making press joints in all standard press
fitting systems on steel pipes, stainless steel pipes,
copper pipes,
plastic pipes, composite pipes
ROLLER'S Uni-Press, Uni-Press 2000, Uni-Press ACC,
Multi-Press, Multi-Press ACC
Radial presses for making press joints in all standard press
fitting systems on steel pipes, stainless steel pipes,
copper pipes, plastic pipes, composite pipes
Axial presses for making compression sleeve joints (sliding
sleeve joints) on stainless steel pipes, steel pipes, copper
pipes, plastic pipes, composite pipes and for expanding
plastic pipes, composite pipes
ROLLER'S Akku-Exparo Mini Q & E for expanding tubes/coils
of the System Wirsbo Quick & Easy
ROLLER'S Akku-Exparo Q & E for expanding of PE-X pipes
for the System Wirsbo Quick & Easy
1.3. Thrust / pressing power
Thrust of radial presses (up to Ø 108 mm)
Pressing power of radial presses (up to Ø 108 mm)
Thrust of radial press Mini (up to Ø 40 mm)
Pressing power of radial press Mini (up to Ø 40 mm)
Pressing power ROLLER'S Axial-Press 5
Pressing power ROLLER'S Axial-Press 15
Pressing power ROLLER'S Axial-Press 40
1.4. Electric Data
ROLLER'S Uni-Press E,
ROLLER'S Uni-Press ACC
ROLLER'S Uni-Press 2000,
ROLLER'S Axial-Press 5
ROLLER'S Multi-Press,
Axial-Press 15/40, Akku-Exparo
ROLLER'S Multi-Press Mini ACC
Akku-Exparo Mini
Rapid charger (1h)
Voltage supply
230 V
1.5. Dimensions
572100
ROLLER'S Uni-Press E
572000
ROLLER'S Uni-Press 2000
577000
ROLLER'S Uni-Press ACC
578000
ROLLER'S Multi-Press Mini ACC 288×260×80 mm (11.3"×10.2"×3.1")
571000
ROLLER'S Multi-Press,
571001
Multi-Press ACC
576000
ROLLER'S Axial-Press 5
573001
ROLLER'S Axial-Press 15/40
573005
ROLLER'S Akku-Exparo Mini
575002
ROLLER'S Akku-Exparo
575001
571513 1.6. Weights
571510
ROLLER'S Uni-Press E drive unit
571535
ROLLER'S Uni-Press 2000 drive unit
565220 ROLLER'S Uni-Press ACC drive unit
570280 ROLLER'S Multi-Press Mini ACC without battery
570280 ROLLER'S Multi-Press drive unit without battery
570280 ROLLER'S Axial-Press 5 drive unit
571280 ROLLER'S Axial-Press 15/40 drive unit without battery 4.3 kg
ROLLER'S Akku-Exparo Mini drive unit without battery 2.0 kg
576280
ROLLER'S Akku-Exparo drive unit without battery
573280
ROLLER'S battery 12 V, 1.3 Ah
ROLLER'S battery 12 V, 2.0 Ah
575280
Pressing tongs Mini (average)
573280
Pressing tongs (average)
Pressing heads (pair, average)
Expanding head (average)
1.7. Noise information
Emission at workplace
Ø 10–28 mm
Ø 10–40 mm
Ø 12–76 (108) mm
1.8. Vibrations
Weighted effective value of acceleration
Ø 12–32 mm
up to Ø 32 mm
Ø 15–40 mm
230 V 1~; 50-60 Hz; 400 W; 1.8 A
S3 15% (AB 2/10 min)
all-insulated (73/23/EWG)
interference-suppressed
(89/326/EWG)
230 V 1~; 50-60 Hz; 500 W; 2.2 A
S3 15% (AB 2/10 min)
all-insulated (73/23/EWG)
interference-suppressed
(89/326/EWG)
12 V =; 2.0 Ah; 20 A
12 V =; 1.3 Ah; 18 A
Input 230 V~; 50-60 Hz; 1.0 A
12–18 V – - --; 50 W; 2.65 A
Output
Input 230 V~; 50-60 Hz
12 V – - --; 1.0 A
Output
430×110×85 mm (16.9"×4.3"×3.3")
435×230×85 mm (17.1"×9.1"×3.3")
365×235×85 mm (14.4"×9.2"×3.3")
338×290×85 mm (13.3"×11.4"×3.3")
315×200×80 mm (12.4"×7.9"×3.1")
330×320×85 mm (13"×12.6"×3.3")
293×248×80 mm (11.5"×9.8"×3.1")
300×290×85 mm (11.8"×12.6"×3.3")
4.4 kg
4.8 kg (10.5 lb)
4.6 kg (10.0 lb)
2,1 kg
4.5 kg
3.5 kg
3.2 kg
0.45 kg
0.7 kg
1.2 kg
1.8 kg
0.27 kg
0.16 kg
ROLLER'S Uni-Press E + 2000
ROLLER'S Uni-Press ACC
ROLLER'S Multi-Press Mini ACC
ROLLER'S Multi-Press
ROLLER'S Axial-Press 5
ROLLER'S Axial-Press 15/40
ROLLER'S Akku-Exparo Mini
ROLLER'S Akku-Exparo
eng
32 kN
100 kN
24 kN
70 kN
5 kN
15 kN
40 kN
(9.6 lb)
(4,5 lb)
(9.8 lb)
(7.8 lb)
(9.4 lb)
(4.4 lb)
(7.0 lb)
(1.0 lb)
(1.5 lb)
(2.6 lb)
(3.9 lb)
(0.6 lb)
(0.3 lb)
82 dB(A)
77 dB(A)
72 dB(A)
73 dB(A)
81 dB(A)
75 dB(A)
77 dB(A)
73 dB(A)
2.5 m/s 2