CAME PXC99W Manuel De Programmation page 64

Control unit info
The valid procedure for the control unit ID information, after access-
ing the Installer/Technical menu, is as follows:
CONTROL UNIT 27 VERSION
(▲)/(▼) (*)
through the Control Unit's Model, Firmware version and Build ver-
sion
Recording audio messages
As well as being able to record these within each procedure for
configuring areas, scenarios, keys, etc , recordings can be made all
at once following this procedure which, after accessing the Install-
er/Technical menu, is as follows:
; with
VOICE 28 RECORDINGS
(▲)/(▼) (*)
messages to be recorded
SEL. VOICE MSG COMMON MSGS 001
SEL. VOICE MSG AREAS 001
SEL. VOICE MSG SCENARIOS 001
SEL. VOICE MSG OUTPUTS 001
SEL. VOICE MSG INPUTS 001
SEL. VOICE MSG KEYS 001
SEL. VOICE MSG CODES 001
and press to start recording
(*)
Press button to listen to the recorded message, or press button
(A)
to record a new one, deleting the existing one
(B)
The recording time begins when you start to speak; press
interrupt it, to exit
(#)
Radio sirens
To customise the settings of each radio siren associated with the
system, after accessing the Installer/Technical menu, the procedure
is as follows:
RADIO SIRENS 29 MOD. WL SIRENS
(▲)/(▼)
through the options and press
shows the default value of the property With
time
Associated areas
ASSOC. AREAS
###
Associated areas are the areas which can be managed by the siren
These also represent an AND-type filter on the areas managed by
the system
The siren tamper (tampering) notifications are only associated with
area 1 To have these notifications at least one radio siren must be
associated with area 1
Radio siren learning
LEARN
*=OK #=ESC
To associate the radio siren with the system
; on the second row it will scroll
you can browse through the
(▲)/(▼)
(*)
; with you can browse
(*) (▲)/(▼)
The display illustrated always
(*)
you can exit at any
(#)
(+)/(‒)
001
(+)/(‒)
Radio supervision
SUPERVISION 001
To activate a technical alarm when an 'up and running' signal
is received from a radio device for more than the time set on
SUPERVISION TIME
Exit time warning
NOT.EXIT TIME 001
To activate a visual warning from siren 01, of system arming/dis-
arming or of open inputs during arming
With choose whether or not to activate visual warnings If
(+)/(-)
is set, the radio siren 01 LEDs will flash every 3 seconds If, during
the exit time, some areas associated with siren 01 are not ready (at
least one input open), the siren LEDs will flash twice every 3 sec-
onds until the areas are ready If the input is then closed (the area is
therefore ready), the visual warnings will be repeated
System armed warning
NOT. AREAS ON 001
To activate a visual warning from siren 01 that the system is on/off
With choose whether or not to activate visual warnings If
(+)/(-)
set, once all the areas are armed the siren's LEDs will flash quickly
once for 3 seconds
to
If a new area is then armed, the system armed warning will not be
repeated
Areas off warning
NOT. AREAS OFF 001
To deactivate a visual warning from siren 01 that the system is on/
off
With choose whether or not to activate visual warnings If
(+)/(-)
set, once all the areas are armed the siren's LEDs will flash quickly
3 times for 3 seconds
If a new area is then armed, the system armed warning will not be
repeated
Radio siren description
MOD.WL SIRENS 001
WL
(▲)/(▼)
Lets you edit the description of the siren
With the keys you can move horizontally, with the alphanumer-
(+)/(-)
ic keys you can edit the description letter by letter
NO
(+)/(‒)
NO
(+)/(‒)
NO
(+)/(‒)
NO
(+)/(‒)
(*)
SIREN 001
WL SIREN 001
DESCRIPTION 001
(+)/(-)
YES
is
YES
is
YES