Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Technical menu
Preliminary information
Accessing technical menu
To start up the system and then programme it by keypad, access
the Installer Menu (hereafter the Technical Menu)
Depending upon the
TECH MENU ACCESS (CODES
parameter, access to the Technical Menu may or may not be
preceded by the User Code
This parameter can only be changed via PC with PXManager
software
Simultaneous access from more than one keypad to the
technical or user menu is not permitted The Technical Code can
be changed later
DIRECT ACCESS
08:23
16/05/10
ENTER CODE
MENU SELECTION
To access the Technical Menu directly, the system must be off Key
in the Technical Code and then key
digits, confirm entry of the code with
ACCESS PRECEDED BY USER CODE
08:23
16/05/10
ENTER CODE
W
A
I
T
I
*=USER MENU
MENU SELECTION
To access the Technical Menu, key in the User Code then the
Technical Code and finally key
If the code has less than 6 digits, confirm entry of the code with
NB IN ALL THE INSTRUCTIONS THAT FOLLOW, THIS OPERATION
WILL ALWAYS BE CALLED
"ENTER THE TECHNICAL MENU"
WITH NO OTHER DETAILS
All the menu headings are shown in this manual Those
available only from PXManager will be marked with icon
PROGRAMMING MODE
The keypad only lets you program in EASY mode
To access all the available functions, use the PXManager 3 0 0, or
later version, programming software
->
INSTALLER TECHNICAL CODE
(222222)
(A)
If the code has less than 6
(A)
(*)
(123456)
N
G
(222222)
(A)
(A)
System
The system menu is used to define the components of the system
(areas, keypads, readers, etc ), assign addresses to them, and carry
out a whole series of tests
The procedure to configure the system is as follows:
)
Go into the Technical menu, then
; choose the change to the system to be config-
SYSTEM 02
(▲)/(▼)
(*)
ured with
(▲)/(▼)
CHANGE SYSTEM
ASSIGNING ADDRESSES TO READERS
SYSTEM TEST
RS485 BUS
PXGPRS/PXLAN/PXWEB CONFIGURATION
and press
(*)
Then browse through the options with
The value selected is shown in the illustrations on the display,
which always shows the default value of the configuration With
you can exit at any time
Areas managed
MANAGED
The system is considered totally armed if all the areas selected are
on
With the number keys
(0)
aged To set the areas above
number keys
(0)
(3)
Keypads
(*)
To enable/disable any keypads connected on the Bus (maximum 2)
With the number keys
keypad and cannot be enabled/disabled) you can select the key-
pads to be managed To set the keypads above
pad
, press the number keys
(13)
Example: if we key in 3, the display will show
system will include keypad 1 of the Control Unit (not
displayed) and keypad 3 on the Bus.
Readers
To enable/disable any readers
With the number keys
(0)
aged To set the readers above
number keys
(0)
(3)
Example: if we key in 1 the display will show
(▲)/(▼)
AREAS
###-----
(0)/(9)
you can select the areas to be man-
(9)
, for example area
(9)
(13)
KEYPADS
--
(0)/(9)
(keypad 1 is the control unit's local
(0)
(9)
, for example key-
(9)
(0)
(3)
-#
READERS
--
(0)/(9)
you can select the readers to be man-
(9)
, for example reader
(9)
(13)
.
#-
(#)
, press the
. The
, press the
Publicité
Table des Matières
