Device/Input Buttons 4- Ag; Using The Rr-1050Audio Button; Programming The Rr-1050Preload Button; Overview Of Buttons And Controls - Rotel RSP-1068 Manuel D'utilisation

Using the RR-1050
AUDIO Button
A
To operate the RSP-1068 with the remote,
make sure that the AUDIO mode is active by
pressing the AUD button on the remote before
you start. If one of the other buttons (CD,
TAPE, etc.) is pressed, the remote will control
another component, not the RSP-1068. The
AUDIO mode will stay active until another
DEVICE/INPUT button is pressed.
Programming the RR-1050
PRELOAD Button
S
The RR-1050 is programmed at the factory
to operate the RSP-1068. Should the AUDIO
command set on your RR-1050 not operate
the RSP-1068, the programming may have
been inadvertently changed. To restore the
RSP-1068 programming, press the recessed
PRELOAD button on the remote with the tip of
a ballpoint pen.
NOTE: Pushing the PRELOAD button will
erase all custom programming and learned
commands, restoring the RR-1050 to its
factory condition.
Overview of Buttons and
Controls
This section provides a basic overview of the
buttons and controls on the front panel and
the remote control. Detailed instructions on the
use of these buttons a provided in the more
complete operating instructions in the follow-
ing sections. Buttons or controls identified with
a number appear on the front panel. Those
identified with a letter appear on the remote
control. When both a number and a letter
appear, the control is duplicated on both the
front panel and the remote control.

STANDBY Button

1

POWER Button

T
The front panel STANDBY button and the remote
control POWER button activate or deactivate
the unit. The rear panel master POWER switch
must be in the ON position for the remote
standby function to operate.
21

ON/OFF Buttons

H
The power ON and OFF buttons on the remote
provide discrete ON and OFF commands to
activate the unit or put it in standby mode.
The rear panel master POWER switch must
be in the ON position for the remote standby
function to operate.
VOLUME Knob
6
VOLUME Button
I
The large rocker button on the remote and the
large rotary control on the front panel provide
the master VOLUME control, adjusting the
output level of all channels simultaneously.

MUTE Button

= J
Push the MUTE button on the front panel or the
remote once to turn the sound off. An indica-
tion appears in the front panel and on-screen
displays. Press the button again to restore
previous volume levels.
NOTE: Pressing the volume buttons on the
remote also cancels the muting function.
DEVICE/INPUT Buttons
4- AG
The top row of buttons on the front panel plus
the MULTI INPUT button are used to select
source inputs for listening/viewing.
These buttons are duplicated on the remote,
except that the MULTI INPUT button is labeled
EXT. The buttons on the remote have two
functions:
Short press: A short press of any button
changes the device that the remote operates,
but does not change the RSP-1068's input
selection.
Long press: A longer press changes the re-
mote control device and changes the RSP-1068
source input for listening/viewing in the main
room.
NOTE: A long press of the EXT button
changes the input to the 7.1 channel ana-
log MULTI INPUT. Pressing the AUD button
only changes the remote device; there is
no input source associated with this button.

REC Button

w D
Press this button before a long press of any
DEVICE/INPUT button to select a source for
recording. The signal from the selected source
appears at the TAPE OUT and VIDEO OUT
audio connectors.

ZONE Button

q N
Press this button before a long press of any
DEVICE/INPUT button to select a source for
ZONE 2.

UP/DOWN Buttons

These two buttons on the remote are used to
move the cursor up or down to select lines in
the OSD menus. These buttons are also used
in conjunction with the TONE button to make
CONTOUR/TONE adjustments.
+/– Buttons
C
These two buttons on the remote are used to
change settings on a selected line in the OSD
menus. Also used for selecting options in some
surround modes.

Speaker Selection Buttons

These three buttons on the remote are used
to select a speaker or group of speakers for
temporary level adjustments. In addition, the
C button is used in conjunction with the UP/
DOWN buttons for temporary adjustment of
group delay/lip synch.

EQ Button

E
This button on the remote is used to turn on
and off the Cinema EQ feature, a high-cut filter
useful for older movie soundtracks.

LF/HF Knobs

5
These two front panel rotary controls are used
to make temporary adjustments to the tone
or contour settings, boosting or cutting high
frequencies (HF) and low frequencies (LF) of
the speaker or speakers selected in the Contour
Setup menu.
NOTE: Permanent contour adjustments can
be made using the Contour Setup menu.
English
M
B