ahlmann AS11 Manuel De L'opérateur page 268

10.3 Maintenance plan AS 11
4117730A
8.4 8.3 8.2 6.2/8.6 11.1
GB
3.1/3.2/3.3/3.4/4.1/8.1/10.1 5.1 5.2 6.1/8.5 9.1 8.3 5.1 5.2 2.1/2.2/2.3/2.4/4.1/8.1/10.1
Item Designation Specification
*
1 Motor oil MIL-L-2104 C = API-CD
*
2.2 Gear oil with LS additive MIL-L-2105 B = API-GL5-6-LS
*
2.4 Gear oil with LS additive MIL-L-2105 B = API-GL5-6-LS
*
3.2 Gear oil with LS additive MIL-L-2105 B = API-GL5-6-LS
*
3.4 Gear oil with LS additive MIL-L-2105 B = API-GL5-6-LS
*
7.3 Hydraulic oil (4.) DIN 51524 - HVLP 46
8 Grease DIN 51825 - KPF 1/2 N-20
9 Distilled water
Key to symbols
First oil change
First filter replacement or first check
Check; eliminate any problems found
+
Lubricate
Change
*
The marks/the filling and checking
screws are binding
See the operating instructions
Caution
When carrying out maintenance work, heed
the accident prevention regulations!
11.2 10.2 7.4 8.1/8.3
1.1/1.2/1.3/1.4/1.5
Viscosity Amount
acc. to manufacturer ca. 10 l with oil filter
SAE 85 W 90-LS ca. 10 l
SAE 85 W 90-LS ca. 2 x 1.75 l
SAE 85 W 90-LS ca. 8.5 l
SAE 85 W 90-LS ca. 2 x 1.75 l
ISO VG 46, VI > 180 ca. 140 l
as required
as required
Lubrication points (indicated in red)
1. Lubricate bolts every 10 operating hours using
grease DIN 51825 - KPF 1/2 N-20.
2. Lubricate glide points as required and always after
cleaning using grease DIN 51825 - KPF 1/2 N-20.
Oil lubrication points
3. Lubricate joints and toggle levers every 50 operating
hours with motor oil MIL-L-2104 C.
Biodegradable hydraulic oil
4. Ester-based synthetic hydraulic oil,
viscosity class ISO VG 46 VI > 180
Every x operating hours
Maintenance points
1 Engine
1.1 Maintenance according to manufacturer's regulations
8.7
1.2 Dry air filter system
Check maintenance display
1.3 Replace filter element if maintenance display is red
11.1
1.4 Check coolant level
1.5 Check and clean combined engine cooler
2 Rear axle with distribution gear
2.1 Check oil level in axle gear (checking screw)
2.2 Change oil in axle gear
2.3 Check oil level in planetary gear (checking screw)
2.4 Change oil in planetary gear
7.1/7.2/7.3
3 Front axle
3.1 Check oil level in axle gear (checking screw)
3.2 Change oil in axle gear
3.3 Check oil level in planetary gear (checking screw)
3.4 Change oil in planetary gear
4 Axles
4.1 Check fastening (420 Nm)
5 Wheels and tires
5.1 Check air pressure
5.2 Check fastening of wheel nuts (600 Nm)
6 Cardan shaft /ball bearing slewing rim
6.1 Check fastening of cardan shaft (65 Nm)
6.2 Check fastening of ball bearing slewing rim (500 Nm)
7 Hydraulic system
7.1 Replace filter inserts, observe electr. control lamp
7.2 Oil level check (view glass)
7.3 Oil change
7.4 Check and clean hydraulic oil cooler
8 Lubrication points, indicated in red (No.)
+
8.1 Front axle / rear axle ( 6 / 6 )
+
8.2 Bucket unit ( 16 )
+
8.3 Hydraulic cylinder ( 12 )
+
8.4 Attachments ( differing )
+
8.5 Cardan shaft ( 3 )
+
8.6 Ball bearing slewing rim ( 4 )
+
8.7 Full floating axle bearing ( 2 )
9 Battery
9.1 Visual check
10 Brake system
10.1 Service/parking brake: functional and visual check before starting work
10.2 Check loading function
11 Lighting system / fresh air filter
11.1 Functional check before starting work
11.2 Check fresh air filter
max. permissible intervals or
shorter (depending on use)