Safe Operation; Getting Started; Additional Accessories - Evolution RAGE3 Traduction Des Instructions D'origine

(3.7)

SAFE OpERATiON

Always ensure that you have selected the correct
saw blade for the material being cut. Do not use
this mitre saw to cut materials other than those
specified in this Instruction Manual.
When transporting a mitre saw ensure that
the cutting head is locked in the 90° down
position (if a sliding mitre saw ensure that
the slide bars are locked). Lift the machine by
gripping the outer edges of the base with both
hands (if a sliding mitre saw, transport using
the handles provided). Under no circumstances
shall the machine be lifted or transported
using the retractable guard or any part of its
operating mechanism.
Before each use check the operation of the
retractable guard and its operating mechanism
ensuring that there is no damage, and that all
moving parts operate smoothly and correctly.
Keep the work bench and floor area clear of all
debris including sawdust, chips and off-cuts.
Always check and ensure that the speed
marked on the saw blade is at least equal to
the no load speed marked on the mitre saw.
Under no circumstances shall a saw blade be
used that is marked with a speed that is less than
the no load speed marked on the mitre saw.
Where it is necessary to use spacer or reducing
rings these must be suitable for the intended
purpose and only as recommended by the
manufacturer.
If the mitre saw is fitted with a laser it shall not
be replaced with a different type. If the laser
fails to operate it shall be repaired or replaced
by the manufacturer or his authorised agent.
The saw blade shall only be replaced as
detailed in this Instruction Manual.
Never attempt to retrieve off-cuts or any other
part of the work piece until the cutting head is
in the raised position, the guard is fully closed
and the saw blade has stopped rotating.
12
www.evolutionpowertools.com
(3.8)
pERFORM CUTS
CORRECTLY & SAFELY
Wherever practicable always secure the work
piece to the saw table using the work clamp
where provided.
Always ensure that before each cut the mitre
saw is mounted in a stable position.
If needed the mitre saw can be mounted on
a wooden base or work bench or attached to
a mitre saw stand as detailed in this Instruction
Manual. Long work pieces should be
supported on the work supports provided or
on appropriate additional work supports.
(2.8)
WARNiNG:
the operation of any mitre saw
can result in foreign objects being thrown
towards your eyes, which could result in severe
eye damage. Before beginning power tool
operation, always wear safety goggles or safety
glasses with side shield or a full face shield
when needed.
WARNiNG:
If any parts are missing, do not
operate your mitre saw until the missing parts
are replaced. Failure to follow this rule could
result in serious personal injury.
(3.9)
ADDiTiONAL SAFETY ADViCE
CARRYiNG YOUR MiTRE SAW
WARNiNG:
When using electric tools basic
safety precautions should always be followed
to reduce the risk of fire, electric shock and
personal injury including the following.
READ all these instructions before attempting to
operate this product and save these instructions.
Safety Advice:
• Although compact, this Mitre Saw is heavy. To
reduce the risk of back injury, get competent
help whenever you have to lift the saw.
www.evolutionpowertools.com
• To reduce the risk of back injury, hold the
tool close to your body when lifting. Bending
your knees so you can lift with your legs, not
your back. Lift by using the handhold areas at
each side of the machines base.
• Never carry the Mitre Saw by the power
cord. Carrying the Mitre Saw by the power
cord could cause damage to the insulation
or the wire connections resulting in electric
shock or fire.
• Before moving the Mitre Saw tighten the
mitre and bevel locking screws and the
sliding carriage locking screw to guard
against sudden unexpected movement.
• Lock the Cutting Head in its lowest position.
Ensure that the Cutting Head Locking Pin is
completely engaged in its socket.
WARNiNG:
Do not use the blade guard as a
'lifting point' . The power cord must be removed
from the power supply before attempting to
move the machine.
• Lock the Cutting Head in the down position
using the Cutting Head Locking Pin.
• Loosen the Mitre Angle Locking Screw. Turn
the table to either of its maximum settings.
• Lock the table in position using the Locking
Screw.
• Use the two carry handle cut-outs machined
into either side of the machine base, to
transport the machine.
place the saw on a secure stationary work
surface and check the saw over carefully.
Check particularly the operation of all the
machines safety features before attempting to
operate the machine.
(4.1)
GETTiNG STARTED - UNpACKiNG
Caution: This packaging contains sharp
objects. Take care when unpacking. This
machine could require two persons to lift,
assemble and move this machine. Remove
the machine, together with the accessories
supplied from the packaging.
13
Check carefully to ensure that the machine
is in good condition and account for all the
accessories listed in this manual. Also make
sure that all the accessories are complete. If any
parts are found to be missing, the machine and
its accessories should be returned together in
their original packaging to the retailer.
Do not throw the packaging away; keep it safe
throughout the guarantee period. Dispose
of the packaging in an environmentally
responsible manner. Recycle if possible. Do
not let children play with empty plastic bags
due to the risk of suffocation.
(4.2)
iTEMS SUppLiED
• Instructions
• Hold Down Clamp
• Blade Change Hex Key
• Side Extension Hex Key
• Multipurpose Blade
• Extraction Port Adapter Tube
• Exhaust Port Plug
(4.3)
OpTiONAL ACCESSORiES
(NOT SUppLiED)
In addition to the standard items supplied
with this machine, other accessories are
available to enhance its performance.
These include the following items:
Description part N°
DIAMOND210
Evolution
or
Diamond Blades
DIAMOND255
EV3S174 or
Dust Collection Bag
SR3S174
Workpiece Support Bars EV3S1 or SR3S1
End Stop EV3SM3 or
(Repetitive Cutting) SR3SM3
Additional accessories and information on
the use and type of accessory suitable for your
machine can be obtained by contacting your
local dealer or Evolution Power Tools.
EN
DE
FR
IT
JP
NL