Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Producing Bevelcuts
•
Fix the workpiece with the clamp as shown.
•
Loose the adjustment lever and set the angle required.
•
Confirm the holing prop is in the saw line.
•
Fasten up the adjustment screw. Turn the tool on and
press the saw down to carry out required cut.
Producing Crosscuts
•
Adjust the cross fence into one of two grooves on the
table and set the angle required.
•
Turn the tool on and with the cross fence slide it slowly
towards the running saw.
Attention: Hold the carried workpiece firmly but never
the part which is going to be cut off.
Holing prop setting (pict. 17+25)
•
Loose the bolt on holing prop (pict.25) to let it shift – see
relevant cut.
•
Tight the bolt back up
Maximum cuts:
The distance between the saw table and the upper edge of
holing prop is about 10cm.
Chips suction
If running the tool in confined places, it is needed to use
proper suction unit or the dust bag, which is part of the
delivery, must be put on the outlet nozzle (pict. 31)
Safety instructions for operators
•
All protective and safety equipment must be mounted
properly and in place before running the tool.
•
Never cut such a wood pieces that cannot be fixed
safely.
•
Saw blade must rotate freely.
•
If cutting already processed wood, watch out for nails,
bolts etc. Remove all objects before work.
•
Confirm before pressing the main switch that the saw
blade is mounted correctly and all moving parts are
oving freely.
•
If any doubts seek qualified advice at authorized Service
center.
•
Read the instruction manual carefully before operation.
•
Observe all safety precautions stated in the manual.
•
Be responsible towards other people.
How to proceed step by step
Desktop saw
1.
set the rulers and fences according to required cut.
2.
turn the tool on.
3.
slide the workpiece slowly under the saw blade until the
cut is finished.
4.
turn the saw off and wait until the blade stops
completely.
5.
now remove the workpiece.
Bevel and miter saw
1.
carry out above stated adjustments on the tool according
to required cut.
2.
fix the workpiece with designed clamp.(pict.1/7).
3.
turn the tool on.
4.
press the saw slowly down to execute the cut.
5.
turn the saw off and wait until the blade stops
completely.
6.
now remove the workpiece.
Malfunctions-causes-elimination
Attention: first of all check the overcurrent fusses!
Motor is not running
1.
The tool is without power
Check electric distribution and power cord, seek
qualified advice.
2.
Heat sensor cut the power off
Wait 5 to 10sec. and then turn the tool on again.
Motor went off during the work
1.
heat sensor is defective. Have it replaced by an
electrician expert.
2.
motor safeguard turns it off from some reason.
wait 5 to 10 sec. and then turn the tool back on again.
Overloading reasons
1.
Power cord is too long or has small diameter. Secure
proper extension cable with minimum diameter of 1,5
2
mm
2.
Saw blade is not sharp enough. Sharp it up.
Saw blade teeth have not sufficient rake.
Burned marks on the workpiece
1.
saw blade is dull. Let it sharpen up or eplace it.
Inspection and maintenance
Plug the cord out before any activity
•
to clean plastic parts use a damp cloth. Never use any
detergents, neither dissolvents or sharp tools.
•
Remove dirt of the table with proper cleaning spray.
•
If it takes more then 10sec. to stop the motor, replace
the worn out brakeparts in qualified workshop.
•
Ventilation holes and moving parts always clean up from
the dust with soft brush after each use.
Lubricate metal moving parts regularly.
Saw blade mounting and dismounting (pict. 29+30)
Attention! Always disconnect the power plug before any
maintenance or adjustment and before removing or
installing the saw blade.
•
Press the lever (pict. 29) and hold it to loose the saw blade.
•
To loose adjustment bolt holding the saw blade use socket
wrench or open-ended wrench. Loose the bolt clockwise
(pict.30).
•
Take the saw blade off the spindle and remove it.
•
Clean the spindle up and put a new saw blade on.
•
Put a new saw blade on and secure it in opposite way as
described above.
•
Attention! Check the rotation direction. Confirm that
cutting edge of teeth match with the direction of rotation,
i.e. forward. Watch out for the arrows on the saw blade
and saw blade guard.
•
Every time before use check if all protective and safety
equipment function correctly.
•
Important! After you mounted on a new saw blade check
by hand if it spins freely.
•
Then plug the power back in and trial run the tool before
you start working on it.
16
Publicité
Table des Matières
