Güde GFO 1801 Traduction Du Mode D'emploi D'origine page 13

• Before start of the tool ensure that data on the product
label match with the parameters of the power supply.
• When using extension cord, ensure that the wire
diameter is sufficient for the stated input. It must be
2
minimum 1,0 mm .
•
Keep the tool table and whole working area clean and
tidy, remove all objects you are not going to need.
•
Watch out for the obstacles around the tool you could
trip over, like power cord.
•
Person operating the tool should not be disturbed.
•
Check the rotation direction of the motor and saw blade
match together.
• Never try to stop rotating saw blade by pressing your
hand, after you turned it off.
• Always use perfect blades only, well sharp, cracks and
deformation free. Replace faulty blades immediately.
• Ensure that the arrow on the blade and the motor show
the same direction.
•
Never remove any safety equipment form the tool.
•
Damaged safety equipment has to be replaced
immediately.
•
If disturbed while working with the tool, first stop the
work you are doing than lift up your eyes.
•
Workpiece must stay on the tool table. Never have it out
of the table if you want to cut it.
• Always keep your hands in safe position, so they cannot
slide and touch the blade.
• If working with workpiece that overhang the table use an
outboard stand to provide support. So the tool will not
cross and chew.
• Confirm that the workpiece is free of nails or other
foreign objects. While using the tool stand always
sideway towards the blade.
•
Never force the tool, because it rotates slower and is
overheating.
•
Never cut more then one workpiece.
•
Always use feeding adapter.
•
Never try to remove any chips or wood pieces or
jammed workpiece before you turn the tool off and
unplug the power cord.
• While doing repairs first turn the tool off and unplug the
power cord.
• Any adjustment, measuring, cleaning, etc. can be done
after you turn the tool off and unplug the power cord.
•
Never leave the workplace unattended when the motor
is running and the power cord is plugged in the
receptacle.
•
Confirm all safety gear of the tool is well mounted back
after doing maintenance.
•
It is necessary to know all safety rules in force on the
workplace.
•
In confined places you must use the dust sucking unit.
•
This table, bevel slide miter saw should be connected to
230 V/16A power source.
• Use the power cord only for designed purpose.
• Confirm proper footing and balance while working.
• Always check the safety equipment of this tool before
use. Check if lightly damaged parts are working properly.
•
Always check if all moving parts are working properly.
Particularly check if the parts are not damaged or
jammed. All parts must be well mounted and work
perfectly.
•
If not stated in this instruction manual, all repairs or
replacement of damaged parts and safety equipment
can be conducted by authorized Service center only.
•
Damaged switches can be replaced by authorized
Service Center.
• This tool complies with all corresponding safety
instructions. Repairs can be conducted by a qualified
electrician only in authorized Service Centers, while
using original replacement parts. If this recommendation
is not observed, this increases risk of injury.
• Never use this tool for rabbeting and notching, etc. If so,
then only with proper safety measures over the table.
(closed all around).
•
This tool cannot be used to produce saw-cut joints.
Emergency Action
Apply the first aid adequate to the injury and get qualified
medical assistance as quickly as possible. Protect the injured
person from more accidents and calm him/her down.
For the sake of eventual accident, in accordance with DIN
13164, a workplace has to be fitted with a first-aid kit. It is
essential to replace any used material in the first-aid kit
immediately after it has been used. If you seek help, state
the following pieces of information:
1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)
Symbols explanation
There are used following symbols in this instruction manual
and on the tool:
Product safety:
This product complies with
corresponding standards of
EC
Restrictions:
Overall restriction
(in connection with other
pictogram)
Cautions:
Caution/Attention
Orders:
Use eye protection
Read the instruction manual
before use
Use safety gloves
Environment:
Don't litter, dispose the waste
correctly
Damaged and liquidated
electric or electronic devices
has to be handed over in
designated places for
recycling.
13
Tool is provided with
protective insulation
Don't touch rotating parts
Warning high voltage
Use ear protection
Use head protection
Cardboard wrapping can be
disposed in designated
places only.