Güde GFO 1801 Traduction Du Mode D'emploi D'origine page 15

Operation requierements
Operator must read and understand this instruction manual
thoroughly.
Qualification
Except detailed training by a skilled person no other special
qualification is necessary to operate this tool.
Operator´s age
Operator must be at least 16 years old. Except the youths
under training and supervised by an instructor.
Training
Operating this tool requires only short training. Special
training is not necessary.
Technical data
Power source:
Max. output:
Revolutions:
Protection category:
Diameter of saw blade:
Table size:
Cross cutting mode:
Max. cutting depth at 0°/0°:
Max. cutting depth at 45°/45°:
Max. cutting depth at 0°/45°:
Max. cutting depth at 45°/0°:
Operating Table:
Max. cutting depth at 0°:
Max. cutting depth at 45°:
Weight cca.:
Article No.:
Transport and storage
• If stored for longer time, it needs to be cleaned properly.
• To avoid injuries keep the blade down while storing.
• Use plastic board or cardboard for weather protection
Mounting and first operation (Pict. 2+3+4)
Fold the main part back (pict. 2) and then easily set the
legs into working position.
Loose locking bolts for the legs release. Then fasten it back,
so all four legs are fixed.
Now stand the saw up.
Using as a Desktop circular saw (pict.
4+5+6+7+8+9+10+11)
To use the saw as a desktop saw, press the lever (pict.4)
down and turn the table until it clicks.
Now loose the wing nut (pict.5) which holds holing prop. In the
holding cylinder of the holing prop there are two grooves
allowing two different settings.
Move with the saw handle to adjust the saw blade guard.
(pict.6) pull the guard up and place the holing prop as showed
on pict. 7. Then tight up the wing nut again.
Confirm that the distance between holing prop and
saw blade is sufficient.
Now turn the bolt (pict.8) to the limit, so the saw unit bends
down.
GFO 1801
230 V/50 Hz
1800 W/P1
-1
4200 min
II
254x20 mm/60 Z
558x500 mm
65x155 mm
40x105 mm
65x105 mm
40x155 mm
70 mm
50 mm
42 kg
55173
15
Now use the handle (pict.9) and turn the table until it clicks.
Pressing the button on the saw blade guard (pict.10) can fix
the guard to the holing prop. If you are not going to use
suction, attach the dust bag to the suction outlet under the
table.
Bevel ruler (pict.11) or straight leading ruler (pict.11) place in
such a way as is obvious from the pict. 11.
Now the saw is ready in desktop setting.
Using as bevel or miter saw. (Pict. 9+13+15+16+17+18)
To use the saw as bevel or miter press the lever (pict.9) to
unlock the table and then you can tilt it over. At the end you
will hear a click sound.
Pull out the orange knob (pict.13) and turn it to let it snap in.
Now erect the saw unit.
Attention
You can set the depth limiter by the lever (pict.14).
Attention
Change the position of the holing prop by the wing nut
(pict.15) holing prop must be pushed back to be parallel with
the saw blade. See pict.16. Use the opposite groove to do so,
same as with the desktop setting.
Attention.
To set the height (pict.17), turn the adjustment screw to the
right completely. (Opposite way as with the desktop setting).
Place the lower guard for bevel and miter setting as shown on
pict.18 under the turntable. First hang the guard into two
designed lugs on the table and then tight it up on the other
side by the delivered screw. (pict. 19). If you are not going to
use the suction, put the dust bag on one of the suction
outlets.
Now the saw is ready to operate in bevel and miter
setting.
Operation
Before each saw adjustment and modification pull
the plug out of the power supply.
Setting the saw angle (pict. 20+21)
• Setting the saw angle from 0° to 45° you can do by
reading on scale. By releasing the adjustment lever and
inclining the saw unit you can change the saw angle
easily. (pict.20)
•
By loosing the adjustment screw and turning the saw
unit, you can change position of the saw blade.
(pict.21).
Turning ON and OFF
•
To turn the tool on press the "green button I"
•
To turn it off press the "red button O"
The tool is equipped with the "emergency switch"
Linear cuts
• Set the parallel ruler towards the saw blade to get
required width.
• Put the workpiece on the table, flat resp. wider side
down.
Attention: keep adequate safety distance form the saw
blade.