Safety Instructions Operator; Safety Instructions User; Safe Storage, Transport, And Assembly - haacon C1-160 Manuel D'utilisation

3.2 safety instructions operator

The operator is obligated to plan and monitor all necessary
measures to guarantee safe operation.
The operator must ensure:
– The use is as intended (Chapter 2.4).
– The safety of the device is analysed according to its appli-
cation and environmental conditions and that recognizable
risks (e.g. danger of injury at rope inlet and rotating drum)
are assessed and eliminated.
– Before commissioning, the device has been examined and
approved according to the appropriate international and
national regulations.
– Operation is only carried out in a perfect, functional condition
– The safety devices are regularly examined for their effectiveness,
GB
only ropes are used, which correspond to a valid standard and
are suitable for the application case. (Chapter 5.3)
– personal protection equipment for the assembly, operation,
maintenance and repair personnel is available and used.
– The operating manual must always be available at the device's
operational location in a legible and complete condition.
– Only qualified and authorised personnel may operate,
maintain, examined, and repair the device.The personnel has
been regularly instructed on all appropriate issues concer-
ning industrial safety and environmental protection, and is
familiar with the operating instructions and in particular with
the therein contained safety instructions.
– The permissible load is clearly recognizable for the user.
– Signs not to be removed from the device and remain legible.
– No substantial changes have been carried out on the device.
– Required tests have been carried out and documented.
– The used spare and wearing parts correspond to the tech-
nical requirements specified by the manufacturer. This is
guaranteed for original spare parts.
– take measures against unauthorized use (key switch)

3.3 safety instructions user

All persons, who operate the device independently must be
suitable for this purpose, familiar with the valid safety and
accident protection regulations and have been assigned by the
operator.
Only use the device when it is in a technically perfect condition
and as intended (Chapter 2.4), with regard to safety and dan-
gers, while considering the operating instructions.
Please check:
z Are the necessary safety devices (Chapter 3.1) present and
functional?
z Have the checks before beginning work been done?
z Is personal protection equipment worn, as required by local
regulations?
– Do not work negligently!
z Stop defective device immediately and inform superior.
z First repair defects, then continue working.
z Replace damaged load carrying equipment and ropes. Re-
pairs are not allowed.
– Only use original spare parts.
– Do not modify or alter the device. Attachments may neither
impair safety nor function.
094323_n_de_gb_fr_eseilwi_v haacon hebetechnik gmbh – Telefon +49 (0) 9375 - 84-0 – Fax +49 (0) 9375 - 84-66
The following is prohibited:
Transport of passengers for commercial purposes
Touching the drum and rope intake during operati-
on.
Work on live components.
Never:
– Loop the rope around the load.
– Pull the lifting rope over stationery parts or edges.
– Exceed the permissible load-carrying capacity.
– Manipulate safety devices.
– Pull or drag loads diagonally.
– Wrench jammed loads away.
– Unreel rope to rope attachment. Two coils must always
remain on the drum.
– Fall of load into the rope or swinging with the load
Avoid to ensure operational reliability:
– Continuous operation, continuous inching operation, excee-
ding of the duty cycle of the motors, as well as remaining
service life according to drive group and load.
Check before lifting the load:
z Is the load suspended safely in the load hook and is it comple-
tely accommodated in the hook? Is the safety flap closed?
For attaching the load, the respective national regulati-
ons for load carrying devices apply (in Germany the
DGUV-I 215-313).

3.4 safe storage, transport, and Assembly

Store clean, dry and protected. Take measures against corrosi-
on on wire rope, hook and brake.
Transport and assembly by authorised persons, familiar with
the valid safety and accident prevention regulations as well as
with the operating instructions.
Please check:
z Are there any transport damages ? (Immediately notify the
supplier).
z Is personal protection equipment worn? (Safety glass, safety
shoes, if necessary helmet).
z Are suitable, standardised and examined hoisting gear and
load securing devices used ? Dimensions and weights
–> technical data (Chapter 4.2).
Always:
– Fasten load securing device to base plate, gear, drum and/or
drum shaft.
– Transport device protected against impacts and shocks,
falling over or toppling.
– Assemble on stable, flat surface.
– Attach the device such a way, that neither the load nor other
effects can change the position the position.
14