Optional Accessories; Options; Necessary Accessories; Installation And Commissioning - Tractel tirak MWX 500-1537 Série Manuel D'installation

6

Optional accessories

The following accessories can also be purchased:
Deflection roller
Adapter or master link
Eye hook or swivel hook
Please directly contact TRACTEL Greifzug GmbH.
7

Options

Please directly contact TRACTEL Greifzug GmbH.
8

Necessary accessories

The following accessories, which are not part of scope of delivery,
are necessary to use the product:
Rigging and securing equipment with an adequate minimum
breaking strength (see 'Structural requirements' on Page 6).
If the rope is deflected or reeved: Rigging and securing
equipment with an adequate minimum breaking strength
(see '3.3 Equipment description, Structural requirements' on
page 6).
A longer connecting cable can be used if necessary, see
'Electrical connection' on page 12.
Other original Greifzug accessories: See '6 Optional accessories'
on page 11.
The operator or the manufacturer of the system is responsible for
selecting and using the accessories in accordance with the local
conditions. You must also abide by any other requirements of the
respectively applicable regulations and standards.
9

Installation and commissioning

9.1

Directives and standards

The product conforms with the following directives and standards:
Machine Directive 2006/42/EC
EN ISO 12100:2010
EN 60204
Machines for lifting loads (transport of materials):
EN 14492-1:2006 + A1:2009
The safety goals required by Directive 2006/95/EC have
been complied with in accordance with Appendix I No. 1.5 of
the Directive 2006/42/EC.
The operator or the system manufacturer is responsible for en-
suring that the machine is used within the limits specified in these
instructions. The operator or the system manufacturer must also
G961.1 - 03/2012
observe the directives and standards and EN ISO 13849 for the
machine in which the unit will be fitted.
9.2 Checks to be undertaken before
starting installation
Check the rigging, deflection rollers and an-
choring points
– Check to ensure that the deflection roller, the rigging and
the on-site anchoring point all have the necessary minimum
breaking strength, see 'Structural requirements' on page 6.
Inspecting the installation site
General
– Check if other components obstruct a correct installation.
The installation space must not contain any sharp or edged
components.
– Free reeler / driven reeler must turn freely.
– Check whether a suitable connection for the power supply in
accordance with chapter 'Electrical connection' on page 12
is available on site.
Check the components and the accessories
General
– Check that the components and the accessories are com-
plete (See '3.2 Scope of delivery' on Page 5 and
'4.2 Components / Modules' on Page 8).
– Check for signs of damage.
– Check that all of the screw connections are tight.
– Replace any damaged parts or have them repaired by a
specialist. Repairs are only to be carried out by a specialist
workshop or by personnel from TRACTEL Greifzug GmbH.
Rope
– Check whether the diameter and design of the rope match
the product and the application, see Table 1 on page II,
Table 7 on page 23 and 'Nameplate and warning signs / ap-
plication restrictions' on page 7.
If the load cannot be guided by on-site means then a rota-
tion-resistant wire rope with a swivel hook or a rope swivel
must be used. Swivel hook and rope swivel must turn freely
when subjected to loads.
– Check that the length of the rope is sufficient:
It must be possible to safely move the load from the start to
the end position.
The lifting path must never be longer than the rope on the
free reeler or driven reeler, as otherwise the rope end switch
will be triggered. In driven reelers the last turn of the rope
must always remain on the rope reel. Rope length details
are listed in Table 3 on page IV.
Installation and operating manual
EN-11