Güde GVZ 1401 2 IN 1 Traduction Du Mode D'emploi D'origine page 25

4) Power tool use and care
a) Do not force the power tool. Use the correct po-
wer tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of child-
ren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety instructions for Scarifier
Operation is only allowed with a safety switch
against stray current (RCD max. stray current of
30mA).
Extension cables must have a cable cross-section of at
least 1.5 mm². We advise against the use of extension
cables of different lengths and cross-sections and the
use of adapters and multi-plugs.
Keep children and other persons including animals in a
safe distance when using the appliance. Minimum safe
distance is 5 m.
Wear personal protective equipment. Wear solid shoes
and long trousers. Never use the appliance when
barefooted or in light sandals. Wear protective gloves if
necessary.
Carefully check the terrain where the appliance is going
to be used and remove all objects that could get caught
or thrown off by the appliance such as stones, branches,
wires, animals, etc.
Avoid operating the equipment in wet grass, where
feasible;
Always inspect the machine before use to
ensure that the rollers and screws are not blunt,
worn or damaged. Replace worn or damaged rollers
and screws to ensure that the machine remains
balanced.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
The appliance must not be used if damaged or
safety equipment is defective. Replace any worn-out
and damaged parts.
Do not start the engine before your feet are in a safe
distance from the cutting tools.
Do not incline the appliance when being started.
Do not start the appliance when you are standing in
front of the ejection opening.
Walk! Never run!
Ensure that you have stable footing, particularly on slo-
pes. Do not use the machine on excessively steep slopes.
Take special care when changing direction on slopes.
Be extremely careful when turning and pulling the
machine towards you.
Always switch off the machine when you are carrying it,
tipping it or moving it when it is not on the lawn. Wait
until all the rotating parts have reached a standstill.
If an undesirable item is encountered or the appliance
starts vibrating, the appliance must be switched off and
the power plug removed. Check whether the appliance
is not damaged. Repair any damage.
Switch the appliance immediately off after finishing
your work.
• Stop the machine and take out the contact key. Wait
until all rotating parts have stopped and the unit has
cooled down.
• Whenever you leave the lawnmower
• To release a blocked blade.
• To adjust the mowing height.
• To empty the collection bag.
• Check the machine if working perfectly after catching
an undesirable object. Repairs must be executed
before putting the machine into operation again.
ENGLISH
21