Meaning Of Different Parameters; Operating Code Display; Programming Code Display; Fault And Breakdown Code Display - SOMFY ELIXO 500 3S RTS Manuel D'utilisation

meaning of different parameters

code description Values (bold = default)
P01 Complete cycle operating 0: sequential
mode
1: sequential + timed close
2: semiautomatic
3: automatic
4: automatic + cell blocking
5: deadman's control (wire)
P02 Complete operating mode 0 to 30 (value x 10 s = time delay value)
automatic timed closing 2: 20 s
P03 Pedestrian cycle operating 0: ident. to complete cycle operating mode
mode
1: without automatic closing
2: with automatic closing
P04 Short automatic closing time 0 to 30 ( value x 10 s = time delay value)
delay in pedestrian cycle 2: 20 s
P05 Long automatic closing time 0 to 50 ( value x 5 min = time delay value)
delay in pedestrian cycle 0: 0 s
P06 Pedestrian opening 1: minimum pedestrian opening
amplitude 9: maximum pedestrian opening
1: 80 cm
P07 Cell safety input 0: inactive
1: active
2: active with autotest via test output
3: active with autotest via power supply switching
4: bus cells
P08 Safety edge safety input 0: inactive
1: active
2: active with auto-test
P09 Programmable safety input 0: inactive
1: active
2: active with autotest via test output
3: active with autotest via power supply switching
P10 Programmable safety input 0: active closing
- function 1: active opening
2: active closing + ADMAP
3: all movement disabled
P11 Programmable safety input 0: stop
- action 1: stop + partial reversal
2: stop + complete reversal
P12 Orange warning light 0: no warning
1: with 2 s warning prior to movement

operating code display

code description
c1 Awaiting command
c2 Gate opening
c3 Awaiting gate closure
c4 Gate closing
c6 Detection in progress for cell safety
c7 Detection in progress for safety edge safety
c8
Detection in progress for programmable safety
c9 Detection in progress for emergency stop safety
c12 Reinjecting current
c13 Safety device autotest in progress
c14 Permanent complete opening wire control input
c15 Permanent pedestrian opening wire control input
c16 BUS cell programming refused
cc1 9.6 V power supply
cu1 24 V power supply

Fault and breakdown code display

code description
e1 Cell safety autotest fault
e2 Programmable safety autotest fault
e3 Defective safety edge autotest
e4
Obstacle detection when opening
e5 Obstacle detection when closing
e6 Cell safety fault
e7 Safety edge safety fault
e8 Programmable safety fault
e10 Motor short circuit protection
e13 Accessories power supply fault
e14 Intrusion fault
e15 Fault when the control box supplied by
the backup battery is first switched on
access to memorised data -
data description
u0 to u1 Complete opening cycle counter
u2 to u3
u6 to u7
Cycle counter with obstacle
detection
u8 to u9
u12 to u13 Partial opening cycle counter
u14 to u15 Reset movement counter
u20 Number of remote controls memorised for complete opening control
u21 Number of remote controls memorised for pedestrian opening control
u22 Number of remote controls memorised for remote lighting control
u23 Number of remote controls memorised for auxiliary output control
d0 to d9 Log of the last 10 faults (d0 most recent - d9 oldest)
dd To clear the fault log: press and hold "ok" for 7 s.
setting
compl.
comments
The cell autotest is not satisfactory.
The programmable safety input autotest is not
satisfactory.
The safety edge autotest is not satisfactory.
Detection in progress on safety input for longer than 3
minutes.
The accessories power supply cuts out following an
overload (excessive consumption)
To access memorised data, select parameter
global [Hundred thousands - ten thousands - thousands] [hundreds - tens - units]
since last auto-programming [Hundred thousands - ten thousands - thousands] [hundreds - tens - units]
global [Hundred thousands - ten thousands - thousands] [hundreds - tens - units]
since last auto-programming [Hundred thousands - ten thousands - thousands] [hundreds - tens - units]
code description Values (bold = default)
P13 Area lighting output 0: inactive
1: controlled operation
2: automatic + controlled operation
P14 Area lighting time delay 0 to 60 (value x 10 s = time delay value)
6: 60 s
P15 Auxiliary output 0: inactive
1: automatic: gate open indicator light
2: automatic: timed bistable
3: automatic: one-touch
4: controlled: bistable (ON-OFF)
5: controlled: one-touch
6: controlled: timed bistable
P16 Auxiliary output time delay 0 to 60 (value x 10 s = time delay value)
6: 60 s
P19 Closing speed 1: slowest speed
at
10: highest speed - default value: 5
P20 Opening speed 1: slowest speed
at
10: highest speed - default value: 5
P21 Closing slowdown zone
1: shortest slowdown zone
at
5: longest slowdown zone
default value: 1
P22 Opening slowdown zone 1: shortest slowdown zone
at
5: longest slowdown zone
default value: 1
P25 Closing torque limitation
P26 Opening torque limitation
1: minimum torque at
P27 Closing slowdown torque
10: maximum torque
limitation
adjusted when auto-programming complete
P28 Opening slowdown torque
limitation
P37 Wired control inputs 0: complete cycle mode - pedestrian cycle
1: opening mode - closing
P40 Coupling speed when
1: slowest speed at
closing
4: fastest speed
P41 Coupling speed when
default value: 2
opening

Programming code display

code description
h0 Awaiting setting
h1 Awaiting start of auto-programming
h2 Auto-programming mode - opening
h4 Auto-programming mode - closing
F0 Awaiting remote control memorisation for operation in complete opening mode
F1 Awaiting remote control memorisation for operation in pedestrian opening mode
F2
Awaiting remote control memorisation for remote lighting control
F3 Awaiting remote control memorisation for auxiliary output control
solution?
Check that "P07" is correctly configured. Check the wiring of the cells.
Check that "P09" is correctly configured. Check the programmable safety input wiring.
Check that "P08" is correctly configured. Check the safety edge wiring.
Check that no obstacles are causing the cells or safety edge to detect.
Check that "P07", "P08" or "P09" is correctly configured in relation to the device connected to
the safety input.
Check the safety device wiring.
Check that the photoelectric cells are correctly aligned.
Disconnect the backup battery and connect the control box to the mains to switch it on for the
first time.
"
ud" and press "ok".
setting
compl.