Programming; Description Of The Programming Buttons; Auto-Programming - Fig; Locking Access To The Parameters (Button A) - Fig - SOMFY Dexxo Compact RTS Manuel D'installation

Dexxo Compact RTS

4 - PROGRAMMING

4.1 Description of the programming buttons

Buttons Function
- Triggers auto-programming
- Memorising/clearing the remote controls
- Modifying the value of a setting
- Using forced operating mode
- Selecting a setting
I n d i c a t o r - Parameter indicator light selected
light A
I n d i c a t o r - Parameter value indicator light
light B - Fault indicator light

4.2 Auto-programming - Fig. 15

[1]. Control the motor with button "A" so that the transmission shuttle is
engaged on the carriage and bring the door to the closed position:
- Keep button "A" depressed to cause the shuttle to move.
- Release the button to stop the movement.
- Keep button "A" depressed again to trigger movement in the opposite
direction.
Release button "A" before forcing the motor on the door.
[2]. Adjust the closed position using button "A".
Release button "A" before forcing the motor on the door.
[3]. Press "B" to launch the auto-programming cycle.
The door performs a complete Opening-Closing cycle.
- If the auto-programming is correct, indicator light B goes out.
- If the auto-programming cycle was not successful, indicator light B
continues to flash (2 flashes).
During auto-programming:
- If the door is moving, the movement is stopped and auto-programming is
interrupted if any of the buttons is pressed.
It is possible to access auto-programming mode at any moment including when
the auto-programming cycle has already been completed.
Note: The remote controls supplied in the kit have already been
memorised.
At the end of installation, it is essential to check that the obstacle
detection complies with appendix A of standard EN 12 453.

4.3 Locking access to the parameters (button A) - Fig.

16
Press button A repeatedly until the indicator light A flashes 4 times.
Press button B once:
- The parameters menu (button A) is locked.
Once installation is complete, the parameters menu must always be
locked to ensure the safety of users.
Failure to follow this instruction may result in serious injury, e.g. due to
crushing by the gate.
At this stage of the installation, the Dexxo Compact RTS drive is
ready to operate.
5
Indicator light key
off
flashing
WARNING
WARNING

5 - OPERATING TEST

5.1 Using the remote controls - Fig. 17

5.2 Obstacle detection operation - Fig. 18 and 19

When an obstacle is detected during closing, the door re-opens (Fig. 18).
When an obstacle is detected during opening, the door will stop
(Fig. 19).
Check that the obstacle detection function works when the door encounters a
50 mm high obstacle on the ground.

5.3 Integrated lighting operation

The lighting comes on each time the drive is switched on. When the door stops
moving, it goes off automatically after 30 seconds. Repetitive use will cause
the light to be lit constantly which may result in the light being switched off
automatically due to thermal protection.

5.4 User training

All users must be trained on how to safely use this door (standard use and
locking principle) and on the mandatory periodic checks.

6 - CONNECTING ADDITIONAL DEVICES

6.1 Description of the different additional devices -
Fig. 20
No. Description
1 Orange light
2 Wired code keypad
3 Key lock
4 Aerial
5 Battery
6 Photoelectric cells
6.2 Electrical connection of the additional devices-
Fig. 20 to 23
Switch off the electrical supply to the motor before performing any operation on
the additional devices.
General electrical diagram (Fig. 20)
Photoelectric cells (Fig. 21)
When positioning the cells, remove the bridge created between terminals 1
and 2.
If cells are removed, it is essential to recreate the bridge between
terminals 1 and 2.
Solar kit (Fig. 22)
Activate solar mode by adjusting the motor power supply type (see below).
Wired code keypad (Fig. 23)
Copyright © 2015 Somfy SAS. All rights reserved