Programming The Remote Controls; Memorising The Keygo Io Remote Controls; Memorising The 3-Button Remote Controls; Programming On An Io Light Receiver - SOMFY DEXXO SMART io Manuel D'installation

EN
Px Door type
Values 1: Sectional
2: Side
3: Up-and-over
NB
If the parameter has been modified a er
auto-programming, the drive returns to non-con-
figured mode. Auto-programming must be
performed again.

8. PROGRAMMING THE REMOTE CONTROLS

8.1. Memorising the Keygo io remote controls

8.1.1. Via the programming interface
1) Press the "PROG" button for 2 s.
The integrated lighting and "PROG" indicator light are lit constantly.
Pressing "PROG" again allows you to memorise the next function
(partial opening, Aux 230 V output control, integrated lighting control).
2) Briefly press the outer le and right buttons on the remote control
simultaneously.
3) Briefly press the button selected to control the function (complete
opening, partial opening, Aux 230 V output control, integrated lighting
control).
Complete opening control - Fig. 17
Partial opening control - Fig. 31
Aux 230 V output control - Fig. 32
Integrated lighting control - Fig. 33
8.1.2. By copying a previously memorised Keygo io
remote control - Fig. 34
This operation is used to copy the programming from a previously
memorised remote control button.
1) Press the outer le and right buttons on the previously memorised
remote control simultaneously until the indicator light flashes.
2) Press and hold the button to be copied on the previously memorised
remote control for 2 seconds.
3) Briefly press the outer le and right buttons on the new remote control
simultaneously.
4) Briefly press the selected button to actuate the drive on the new
remote control.
Key:
Keygo io A = "source" remote control already memorised
Keygo io B = "target" remote control to be memorised

8.2. Memorising the 3-button remote controls

8.2.1. Via the programming interface - Fig. 35
1) Press the "PROG" button for 2 s.
The integrated lighting and "PROG" indicator light are lit constantly.
Pressing "PROG" again allows you to memorise the next function
(partial opening, Aux 230 V output control, integrated lighting control).
2) Press "PROG" at the rear of the 3-button remote control to memorise
the function.
The integrated lighting and "PROG" indicator light flash for 5 s.
9
8.2.2. By copying a previously memorised 3-button
mono-directional io remote control - Fig. 36
Key:
A = "source" remote control already memorised
B = "target" remote control to be memorised
8.2.3. Function of the 3-button remote control buttons
Function
Comp. Complete opening Stop
opening
Part. Complete opening If the door is
opening
Aux 230 V Aux. output ON
Integrated ON
lighting
9. PROGRAMMING ON AN IO LIGHT RE
CEIVER
This function enables automatic activation of remote lighting connected to
the receiver during garage door movements.
3) Switch the light receiver to programming mode (refer to the receiver
manual).
4) Briefly press the "PROG" button.
The integrated lighting and P0 indicator light flash once.
The lighting connected to the light receiver comes on and then goes
out.
10. CLEARING THE REMOTE CONTROLS
AND ALL SETTINGS

10.1. Clearing memorised remote controls - Fig.

37
Press the "PROG" button for 7 s until the "PROG" indicator light flashes.
Clears all memorised remote controls.

10.2. Clearing all settings - Fig. 38

Press the "SET" button for 7 seconds until the "POWER" indicator light
flashes quickly.
Clears the auto-programming and resets all parameters to default values.
11. LOCKING
BUTTONS FIG. 39
Warning
The keypad must be locked to ensure user safety.
Failure to follow this instruction may result in serious injury, e.g.
due to crushing by the door.
Press the "SET", "+" and "-" buttons simultaneously.
The programming (auto-programming, parameter setting) is locked. The
parameter setting indicator lights come on when the programming button
is pressed.
To access the programming again, repeat the same procedure.
DEXXO SMART io
my
Complete closing
Complete closing
closed or open
partial opening
Otherwise
stop
Aux. output OFF
OFF
THE PROGRAMMING
Copyright © 2018 SOMFY ACTIVITES SA. All rights reserved.