15_Product Modifications; 16_Disclaimer; 17_Name And List Of Components - Elite Drivo II Mode D'emploi

EN
operation of the Drivo II due to such interference.
Do not expose the Drivo II to direct sunlight for long periods
when they are not in use.

15_PRODUCT MODIFICATIONS

Also in view of any technical update, ELITE reserves
the right to make changes to the products or their
specifications without being obliged to notify or inform the
Customer beforehand for:
a) changes that do not affect negatively the product
performance;
b) changes required to meet or improve the product
specifications;
c) changes necessary for the products to comply with the
applicable legal requirements.
ELITE also reserves the right to supply these products
with these improvements without being obliged to or
responsible for applying the same modifications to any
previously purchased products, reserving also the right to
change prices and model availability according to market
conditions, component availability and other corporate
considerations.

16_DISCLAIMER

Elite S.r.l. is not liable for any temporary or permanent
damage to the physical integrity of the user, whether direct
or indirect, resulting from the use of the trainer.

17_NAME AND LIST OF COMPONENTS

Your Drivo II electronic trainer is made of the
following components:
N°1 Drivo II body
N°2 Freehub body spacer
N°1 Chainstay adapter
N°1Left chainstay adapter
L=130-135 mm (5,1-5.3 inches)
N°1 Right chainstay spacer adapter
L=142 mm (5,6 inches)
N°1 Left chainstay spacer adapter
L=142 mm (5,6 inches)
N°1 Power supply
N°1 Quick release
N° 1 Left leg
N° 1 Right leg
N° 1 Central support
N° 2 TBEI M6x60 screws
N° 6 M6 washers
N° 2 M6 nuts
N° 2 TBEI M8x35 screws
50
18_ASSEMBLING THE DRIVO II
- Disassemble the Drivo II body (Ref. A)
- Place the Drivo II body (Rif. A) vertically as indicated
(Pic.1) and hold it in place with the upper handle
- Spread the leg until you can hear the safety lever click
(Pic.2 and Pic. 3).
- Place the home trainer on a flat surface and insert the
side legs (Ref. L and Ref. R) (Pic. 4).
- Screw the M8x60 screws with the washers and the M8
nut (Ref. P – Q – S ) until it touches the side legs and starts
rotating them (Pic. 5).
- Spread the side legs (Ref. L - Ref. R ) to its max extent
(Pic 6).
-The centering pin must be aligned with the bracket holes
(Fig. 7).
- Tighten the safety knob (Pic. 8).
- Insert the central support (Ref. O)(Pic. 9)
- Tighten the screws + M8 washers (Ref. T- Q)(Pic. 10)
- Make sure the hometrainer is stable (Pic 11), otherwise
operate on the adjustable feet (Pic 12A - 12B).
- Warning! the central support must remain at least 3 mm
above ground (Pic. 13).
19_INSTALLING THE SPROCKET CASSETTE
ON THE DRIVO II FOR M5 L=130 MM AND
L=135 MM CHAINSTAYS
- Assemble the sprocket cassette on the freehub by
aligning the groove profiles.
- 2 spacers (Ref. B) are usually needed for the Shimano
/ SRAM 9 speed cassette (Pic. 14), 1 spacer for the 10
®
speed cassette (Pic. 15) and no spacer is required for the
(Ref. A)
11 speed cassette (Pic. 16). Depending on the cassette
(Ref. B)
brand you are using there might be some differences with
the aforementioned general data.
(Ref. C)
- Using the torque wrench, tighten the lock ring supplied
with the cassettes onto the freehub body (Pic. 17).
(Ref. D)
CAUTION!
Strictly follow the instructions provided by the cassette
(Ref. E)
manufacturer with regard to specific installation
techniques, the need for additional spacers and torque
specifications.
(Ref. F)
NOTE: please contact your dealer if you have questions or
(Ref. G)
are unable to install the cassette. The warranty does not
(Ref. I)
cover any damage to the bicycle and/or Drivo II in the event
(Ref. L)
of incorrect installation.
(Ref. R)
- Drivo II includes the correct 5mm diameter quick release
adapter for dropout spacing ranging from 130mm (5,1
(Ref. O)
inches) to 135mm (5,3 inches). Therefore, on bikes with
(Ref. P)
130-135mm (5,1 to 5,3 inches) dropout spacing, insert
(Ref. Q)
the left dropout adapter (Ref. D) (Pic. 18). Please consult
(Ref. S)
the paragraph 21 for bikes with 12mm diameter (0.47 in.)
(Ref. T)
®