Swegon Kit CPT TAC3 Manuel D'installation page 25

10) Airflow/Pressure analogic output signal
Signal between terminals OUT1/OUT2 and GND. 0 - 10 Vdc signal.
With advanced setup it is possible to choose which fan is connected to the output signal. Each output can either be an the
airflow or the pressure of the selected fan. The default selection is airflow of F1 on OUT1 and pressure on F1 on OUT2.
Wiring diagrams : see schematics
DD 9-7TH
1/2
720054
Max. Airflow 2000
Max. Press. 540
DS 11-4
1/2
720062
Max. Airflow 1900
Max. Press. 890
11) Technical Data of the fans
Supply : 230VAC (between 208V and 240V) - Frequency : 50/60Hz
Grounding : ! COMPULSORY !
Electrical protection :
The motor is self-protected against overloading. It is thus NOT necessary to install an electrical overload protection
device. We advise using a short circuit protection device with the following specifications :
- Starting peak of 150 A for 2 to 4 milliseconds. The "softstop" function has to be used to avoid this peak.
- We recommend a class AM protection device.
Recommended protection calibre/motor type
Type
1/3 HP
1/2 HP
3/4 HP
1/1 HP
Indicative non exhaustive list of : a) AM (10x38mm) fuses with manufacturers references, b) references of thermo
magnetic circuit breakers (disjoncteur): select it with D type "slow" reaction curve – cutting power of 10.000A - AC3.
a)
Calibre Legrand
2A réf. :130.02
4A réf. :130.04
8A réf. :130.08
10A réf. :130.10
Insulation class
Thermal : B
Mechanical : IP44 - the connectors must be oriented downwards.
Ambiant temperatures : -10°C / +55°C
– UL approved
Conformities :
12) Technical Data of the Kit CPT TAC3
Supply 230VAC (between 208V and 240V) - Frequency : 50/60Hz
Electrical protection: calibre 4A – slow type
CBr4: Mount passcables (PG) M16 or M20 on the plastic box where you have previously punched out the holes to allow
cable passage. Be cautious to punch holes properly to keep tightness.
Outputs Bypass en R1 relays: 230V – maximum 4A.
Outputs to external relays R1/R2/R3/R4/R5: 12Vdc, 50mA/output.
Ambiant conditions: temperature from -20°C to +70°C, humidity from 5 to 85%.
Conformity: .
.
1 in appendix 1
DD 9-9 DD 10-10 DD 11-11
1/2 3/4
720055 720056 720057
2900 3800 4400
800 1000
DS 12-5 (K)DF 280-114
3/4 1/3
720063 720036/38/77 720037/39/78
2600 1300
1020 360
Calibre
4A
4A
8A
10A
Télémécanique
réf. : DF2-CA02
réf. : DF2-CA04
réf. : DF2-CA08
réf. : DF2-CA10
DP 6-6 DP 9-7TH
1/1 1/2 1/1
720058 720059
2200 3600
985 410 570
(K)DF 280-114 DS 140-60
1/2 75W
720088
1700 400
520 600
b)
Huppertz Calibre
réf. : D440102
réf. : D440104
réf. : D440108
réf. : D440110
DP 9-7TH DP 9-9
1/2 1/1
720011 720060
3000 5700
550 860
DS 140-60 DD 160-160
250W 250W
720089 720099
550 800
620 600
Vynckier
2A réf : 099/37202-000
4A réf : 099/37204-000
8A does not exist
10A réf : 099/37210-000
DS 10-4 TH DS 10-4
1/3 1/2
720071 720061
1000 1500
490 665
Merlin Gérin
réf : 25111
réf : 25113
does not exist
réf : 25115
25