Video Setup - Rotel RAP-1580MKII Manuel De L'utilisateur

28
inadvertently power off. In this case the Automatic Power Off timer
should be set to DISABLED.
MAX POWER ON VOLUME: Specifies a maximum volume level to be
used each time the unit powered on, between 20 dB to 70 dB, in 1
dB increments.
POWER MODE: Enables the rear panel USB power port and the Network
connection to remain powered at all times. The power consumption is
higher in Quick Power mode. To enable continuous power to the rear USB
power port and allow for IP control of Power-On select the Quick option.
Valid settings include: Normal, Quick.
NOTE: When the POWER MODE is configured to Quick, the RAP-
1580MKII will consume additional power in standby mode.
NOTE: Some regions limit the amount of Standby Power Consumption
allowed and the POWER MODE function will not be available. To
control the Rotel product in this case use the RS232 connection. For
questions on the availablity of the Power Option please contact your
authorized Rotel dealer.
SIGNAL SENSE INPUT: Checks if a digital audio signal is present on the
configured Signal Sense Input. When this input is selected as the active
listening source, the RAP-1580MKII monitors the digital data stream to
determine if there is audio. If there is no audio detected for 10 minutes,
the RAP-1580MKII will enter Signal Sense Standby Mode. When in
Signal Sense Standby Mode and the RAP-1580MKII detects audio on
Signal Sense Input, the unit will automatically power on. To disable this
function, select the DISABLE option which is the factory default setting.
NOTE: When the RAP-1580MKII enters standby mode via the remote
control, the Signal Sense function will not operate until the unit detects
the audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.
NOTE: When the SIGNAL SENSE INPUT function is activated, the RAP-
1580MKII will consume additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the Signal Sense
function is not available in all markets.
NETWORK CONFIGURATION: Sets the network configuration for the unit. In
most systems, set the IP ADDRESS MODE to DHCP. This setting will allow
your router to assign an IP address to the RAP-1580MKII automatically. If
your network uses fixed IP addresses, set the IP ADDRESS MODE to Static. A
fixed or STATIC IP address requires manually entering the IP Address, Subnet
Mask, Gateway, and DNS in the IP ADDRESS CONFIGURATION sub menu.
NETWORK CONFIGURATION
IP ADDRESS MODE : DHCP
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK
RAP-1580MKII Surround Amplified Processor
SOFTWARE INFORMATION: Displays the current software installed in the
unit. It shows the MAIN, DSP and STANDBY software versions. There is also
an option to check for software updates. This feature lets the unit search
for software updates on the Internet. The network needs to be properly
configured. Alternatively, you can load the software through the front USB
socket. For more information on the software update process please contact
your authorized Rotel dealer.
RESTORE FACTORY DEFAULT: This option sets the unit back to the original
setting as when it left the factory. All user setting will be erased.
NOTE: Use caution when resetting the RAP-1580MKII to factory
defaults as all user configured options will be erased and reset to
original factory settings.

Video Setup

STANDBY VIDEO SOURCE : Disable
FAST AUDIO SYNC : Disable
OSD FORMAT : 480P
The VIDEO SETUP menu provides configuration of the HDMI outputs. See
the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI
connections.
STANDBY VIDEO SOURCE: Options are "Disable", "HDMI 1-7", "HDMI
Front", or "Last". This allows the selected HDMI source input to pass-through
the RAP-1580MKII while in standby mode. Audio and video are passed
directly to the attached TV or display.
NOTE: When the Standby Video Source is enabled the RAP-1580MKII
will consume additional power when in standby mode.
FAST AUDIO SYNC: This function allows the HDMI audio to sync more quickly
with the RAP-1580MKII. Only 1 input can be selected for this function.
NOTE: Some source devices do not provide the timing requirements
to allow this function to work properly and could result in static noise
before the audio is heard. If this happens please disable that source
input from using this function.
OSD FORMAT: The HDMI On Screen Display output resolution can be
changed from 480p to 576p. The default value is 480p.
Press the BACK button or select "BACK" on the OSD to exit the VIDEO
SETUP Menu and return to the main menu.
VIDEO SETUP
BACK