Proper And Improper Use Of The Machine; General Warnings And Behavioural Norms - Rivacold P Mode D'emploi Et D'entretien

UK
The level of mass acoustic pressure A generated by B
in force, during functioning is less than 70 dB (A).
3.6.2. Vibrations
In use conditions in compliance with the instructions supplied by the manufacturer in this handbook, the vibrations were not such
to create dangerous situations.
The operator however, if vibrations occur, should immediately stop the machine and signal the phenomenon to the
manufacturer's support service.

3.7. Proper and Improper Use of the Machine

The machine was designed and manufactured exclusively for industrial and commercial refrigeration in stable locations.
Blocksystem P and SV were exclusively designed to be installed on vertical walls. Blocksystem SF was designed exclusively to be
installed on horizontal walls (ceiling).
The can exclusively use the refrigerating gas for which it was designed (typically R404A). As an optional the manufacturer
MACHINE
can create machine models capable of using other refrigerating gas (for example R134a). Assess what is reported on the label of
the machine to identify the refrigerating gas for which the machine was designed and manufactured.
The machine was designed and manufactured to work in environments free of a potentially explosive atmosphere and as such
cannot generate a potentially dangerous atmosphere.
The machine must be adequately protected from the weather elements
It is good safety practice to place powder extinguishers near the machine. To prevent the possibility of fire, it is necessary to keep
the machine clean of pieces of plastic, oil, solvents, paper and rags.
The use of the machine for different operations could cause damage to persons or the machine itself and is therefore considered
improper use for which the manufacturer cannot be held responsible.
WARNING:

3.8. General Warnings and Behavioural Norms

To avoid any risky conditions to people or damage to the machine, we recommend you scrupulously follow the general warnings
and behavioural norms reported here.
DANGER:
The operators responsible for machine management must be adequately trained to use it at its best and without risk and
must operate in a comfortable environment that guarantees the best safety and hygiene conditions possible.
DANGER:
Before using the machine, ensure that any dangerous conditions to safety are adequately eliminated and that there are no
operators present in the danger zones near the machine.
Before using the machine, ensure all the guards are in place and that all safety devices are present and efficient.
Warn supervisors of any functioning irregularities in the machine or any problems relating to the integrity of the machine
protections.
Carefully read the machine labels. Do not cover them for any reason and replace them immediately if damaged.
Do not rest liquid containers on the machine.
Consult this handbook on the safety specifications in force and the specific
however, the staff responsible for the machine must wear suitable clothing, by avoiding or paying due attention to:
loose clothing,
wide sleeves,
ties or hanging scarves,
necklaces, bracelets and rings.
Staff responsible for maintenance of the machine must be aware of all the procedures reported in Chapter 6 – Maintenance
and Demolition and be adequately prepared technically to correctly interpret the instructions and diagrams in this handbook
and to intervene on the machine.
The area where the maintenance operations take place must always be clean, dry and with suitable equipment always
available and efficient.
The work area must never be occupied in such a manner to interfere with the free movement of the operator. In case of
emergency, immediate access to the machine must be guaranteed for responsible staff.
In the aforementioned area, access to people who are not directly responsible for machine functioning is forbidden, to avoid
danger due to distraction or negligence during machine intervention.
If intervention has to be conducted near the electrical components, work with dry hands and use dielectric gloves (working
on electrical components with wet hands leads to almost certain danger of electrical shock).
DANGER:
LOCKSYSTEM
in case of a different destination of use, it is indispensible to consult the Manufacturer's Technical
Office in advance.
the manufacturer declines all responsibility for any damage to property and/or persons deriving from
improper interventions conducted by unqualified, untrained or unauthorised staff.
prevent the machine being used by unauthorised staff or untrained staff without supervision: in fact,
before starting work, each operator must be perfectly aware of the position and functioning of all the
controls and features of the machine. Furthermore, the operator must have read this handbook
.
ENTIRELY
you should ensure that before starting any type of machine intervention or corresponding to its
components or accessory equipment to section power; if this is not possible, it is necessary to take
measures to allow you to operate on the machine in safe conditions.
P - SF - SV and measured, following the criteria set by the norms
to implement for personal safety; in particular,
IPD
P-SF-SV Pag. 44 Rev 00 02/11