Putting In The Detergent Solution - Fimap FM43 ORBITALE EXTRA SPRAY Manuel D'utilisation Et D'entretien

4
5
4
5
7. Fix the pump support box (6) to the handlebar pipe using the knobs (7) supplied (Fig.7).
8. Fix the nozzle support bracket (8) in the front of the brush head, using the knob (9) supplied (Fig.8).
9. Connect the power connector of the spray kit (10) to the socket (11) in the control handlebar pre-
assembly (Fig.9).
9
6
7
8
7 8
10. Connect the power supply connector of the brush head motor (12) to the power cable connector (13)
on the control handlebar pre-assembly (Fig.10).
11. Press the handlebar uncoupling lever (14) (Fig.11) and turn the handlebar about forty-five degrees
(Fig.12). When the handlebar is vertical, release the uncoupling lever (14).
14
13
12
10 11
12. Unscrewing the closing knob (15) (Fig.13) position the upper brackets beyond half of the column
(Fig.14) (if they have not already been positioned).
13. Put the solution tank on the column, so that the bottom of the tank is anchored to the fixed bracket
(16) on the column itself (Fig.15).
15
13 14
14. Holding the tank with one hand, move the mobile bracket (17) down until the solution tank is locked
to the column (Fig.16).
15. Lock the position of the mobile bracket (17) by tightening the closing knob (15) (Fig.17).
16. Press the handlebar uncoupling lever (14) (Fig.11) and turn the handlebar to the vertical position
(Fig.18). When the handlebar is vertical, release the uncoupling lever (14).
15
17
16 17
17. Insert the water distribution pipe (18) in the hole on the brush head (19) (Fig.19).
18. Insert the solution tank tap tie chain (20) in the coupling in the tap control handle (21) (Fig.20).
19. Remove the solution tank cap (22) (Fig.21).
21
19
20
18
19 20
20. Disconnect the detergent solution pipe (23) from the quick coupling (24) (Fig.22).
21. Insert the detergent solution pipe (23) into the hole in the solution tank (Fig.23).
22. Connect the detergent solution draught filter (23) to the quick coupling (24) (Fig.24). Make sure that
the draught filter stays inside the solution tank.
23
23
24
22 23
23. Insert the solution tank cap (22) (Fig.25).
24. Lightly tip the machine back (Fig.26), block one of the rear wheels and shift the control column
backwards.
6
25. Turn the brush head to the vertical position. Bring the rotated brush head into contact with the floor
(Fig.27).
6
22
26. Unscrew and remove the tightening keys (25) (Fig.28).
11
27. Remove the pad holder stop flange (26) (Fig.29).
28. Insert the pad holder, being careful to centre the fixing pins (27) in the appliance with the holes (28)
10
in the pad holder (Fig.30).
9
25
29. Insert the pad holder stop flange (26) (Fig.31)
30. Screw in the tightening keys (25) (Fig.32)
31. Lightly tip the machine back (Fig.33), block one of the rear wheels and shift the control column
backwards.
12
32. Turn the brush head into the work position (Fig.34).
26
16
15

16.2. PUTTING IN THE DETERGENT SOLUTION

Fill the solution tank only when the column is in vertical position, by proceeding as follows:
1. Take the device to the dedicated maintenance area.
2. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
18
supply(Fig.1), and if not, disconnect it.
3. Remove the solution tank cap (4) (Fig.2).
22
4. Remove the water distribution pipe (5) in the hole on the brush head (6) (Fig.3).
21
5. Disconnect the detergent solution pipe (7) from the quick coupling (8) (Fig.4).
23
24
6. Remove the detergent solution pipe (7) from the hole in the solution tank (Fig.5).
7. Remove the solution tank tap tie-rod chain (8) in the coupling in the tap control handle (9) (Fig.6).
24
19
25 26
26
28 29
ATTENTION: To tighten the keys correctly use a tightening clamp.
24
31 32
34
N.B.: the place designated for this operation must comply with current environmental protection
regulations.
CAUTION: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
WARNING: To prevent damaging the power cable, disconnect the plug from the mains socket by
directly pulling the plug and not the cable.
3
1
2
1 2
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
27
27
28
30
33
6
5
4
3