Safety Instructions - Güde GF 180 Mode D'emploi

Dear Customer,
Your new device for tile cutting is easy to handle. It
may be used for many purposes, and it is an
indispensable device for home do-it-yourself men. We
wish you to enjoy your new device as much as
possible.
1
Introduction
This device for tile cutting was designed according to
applicable European regulations and standards. When using
electric devices some safety measures shall be principally
made for prevention of potential injuries and damages.
Therefore read carefully this Manual and keep it so that you
may have any time necessary information available.We do not
bear responsibility for the damage occurred due to breach of
the Manual.
2

Safety Instructions

Read carefully the whole Manual before the first use of the
device.If there are any doubts about the connection and
attendance of the device, contact the Manufacturer
(Service Department).
BY CAREFUL OBSERVANCE OF FOLLOWING
INSTRUCTION THE HIGH GRADE SAFETY MAY BE
GUARANTEED.
Caution: The device shall be operated only if
furnished with protection switch protecting the device
against insufficient current (maximum insufficient
current 30 mA according to the VCE regulation, part
02). Please contact your electrician-specialist.
•
Keep order in your working area.
A mess on the workplace may cause injury.
•
Consider the environment aspects.
Do not expose electric devices to rain. Care for good
lighting. Do not use electric devices close to
inflammable liquids or gases.
•
Protect yourself against electrical accidents.
Prevent contact of your body with the earthened
parts, e.g. pipes, heating elements, stoves,
refrigerators. Use the device furnished with protection
switch against insufficient current.
* Keep off the reach of children
Do not permit other persons to handle or contact the
device or the cable, keep these persons off your
working area.
•
Retain your devices safely stored.
When not used, tha devices should be retained in a
dry, closed room, out of the reach of children.
•
Do not overload the devices.
The devices will work better and more safely in the
specified scope of output.
•
Use the correct device
Do not use too weak devices for difficult works. Do
not use the devices for the purposes and works thay
are not designated for.
•
Use suitable working clothes
Do not wear loose clothe or jewelry. They may be
caught by moving parts of the device and cause the
accident to you. When working outside, wear rubber
gloves and slip-resistant shoes. Use hairnet if you
have long hair.
•
Use protective glasses and a respirator
Use always protective glasses, and a respirator at
works where dust is generated.
•
Protective cover
Keep the protective cover over the diamond dividing
wheel always on place.
•
Do not use cable for other purposes
Do not carry the device by means of cable and do not
use cable when pulling it out of the socket. Protect
the cable against heat, oil and sharp edges.
•
Secure the workpiece
Place the workpiece by means of sliding bar or sliding
pin to the running diamond dividing wheel. Make sure
ther shift is even.
•
Do not leave the field designated for standing
Avoid abnormal posture. Care for due posture and
keep balance when working.
•
Maintain your device with care.
Keep your device always clean. Observe the
regulations for maintenance and replacement of the
device. Check regularly plug and cable and in case
they are damaged, have them replaced by an
authorized specialist. Check regularly the extension
cable and replace it if it is damaged. Clean carefully
the working table after every use and protect it
against corrosion by wiping it with a dry cloth slightly
soaked with oil.
•
Pull out the plug
If the device is not used, pull out the plug before
starting maintenance and when replacing diamand
dividing wheel.
•
Do not leave the tool keys in the lock
Before switching on make sure that the tool keys and
setting tools are removed..
•
Extension cables in the outside environment
In the outside environment use only extension cables
approved for such use and marked in corresponding
way.
•
Check if your device is not damaged
Before further use of the device check carefully
protective equipments or slightly damaged
components if their function is faultless and if it is in
compliance with their purpose.
Check if the moving parts function is all right, it these
parts are not jammed or if they are not damaged.
All parts should be correctly assembled and all
conditions should be fulfilled so that the fultless
operation of the device would be waranteed. Faulty
equipment and damaged parts shall be due repaired
or replaced by the customer´s service, unless
otherwise is stipulated in the Manual. The damaged
switches shall be replaced by the customer´s service.
Do not use devices at which the switch cannot be
switched on and off.
Blunt dividing wheels shall be replaced in time, the
electric equipment shall be only repaired by the
electrician-specialist
•
Pay always attention
Folow your work. Proceed sensibly. Do not use the
device if you are not properly concentrated.
•
Caution!
It is in the interest of your personal safety to use only
accessories and additional devices mentioned in the