Safety Instructions - Güde GDS 16 PRO Traduction Du Mode D'emploi D'origine

Introduction
To enjoy your new appliance as long as possible, please
read carefully the Operating Instructions and the attached
safety instructions before using it. Further, we recommend
keeping the Operating Instructions to recall the product
features in the future.
Within the continuous product development, we
reserve the right to make technical changes to
improve it.
Translation of original operating instructions
Supply includes
Take the appliance out of the transport package and check
it whether there are the following parts:
•
1 fretsaw
• 2 saw blades (1 saw blade being
preassembled)
•
1 saw blade cover
• M5x40 saw blade cover installation screw
• M5 saw blade cover installation nut
•
2 Allen keys (assembly tools)
•
1 original Operating Instructions
• Warranty Certificate
Please contact your dealer if any parts are missing or are
damaged.
Appliance + accessory equipment description (pic. A-
B+D)
1. Locking screw
2. Saw blade cover
3. Saw bench
4. Saw bench insert
5. Securing screw
6. Assembly hole
7. Rubber legs
8. Saw blade storing area
9. LED lamp
10. Blowing equipment
11. Rubber leg
12. Assembly hole
13. Stroke number controller
14. On
15. Off
16. Laser On/Off
17. LED lamp On/Off
18. Connection
19. Indicator
20. Scale
21. Dust extractor adapter
22. Saw blade tension lever
23. Laser adjusting screw
24. Laser
25. Upper holder of saw blade
26. Saw blade
27. Inspection cover
28. Bottom holder of saw blade
29. Allen key T-shaped handle
30. Allen key
Technical specifications
Connection:
Protection type:
Max. output:
Revolutions:
(controllable)
Saw blade length:
Cutting output 90°:
Cutting output 45°:
Feeder cable:
Noise L :
WA
Laser wavelength
Laser power:
Dimensions LxWxH:
Weight:
Switch-on time:
The S2 switch-on time of 5 minutes (short operation) means that
the engine may only be subject to continuous load with rated
voltage of 120 W for a time specified on the type label (5 minutes).
Otherwise, the engine could get inadmissibly heated. During a
break, the engine gets cooled down to the initial temperature.
Noise emission values:
The fretsaw noise is measured according to DIN EN ISO 3722;
11/95, DIN EN 11 201. Noise in place of work may exceed 93 dB
(A). In such a case, the user must take anti-noise measures (ear
protectors to be used).
Sound pressure level L :
pA
Sound power level L
WA
"The given values are emission values and therefore do not have
to represent safe values in the place of work. Although there is
correlation between emission and pollutant levels, this is not a
reliable basis for determining whether or not additional safety
measures are necessary. Factors able to influence the current
level of pollutants in the place of work include the time of effects,
type of place of work, other noise sources, etc. e.g. number of
machines and other related processes. Reliable values in the place
of work may also differ in various countries. However, this
information should authorise the user to evaluate better the threat
and risk."
General instructions
•
After unpacking, check all parts for any damage
during transport.
•
Check whether the shipment is complete.
•
Learn with the appliance functions using the
Operating Instructions before using it.
• Original accessory equipment and original wearable
and spare parts to be used only.
•
All covers and safety equipment must be properly
installed before putting the appliance into operation.
See the following points:
Appliance to be used with RCD (safety switch
against stray current) 30mA only!

Safety instructions

CAUTION! Laser radiation
Do not look at class 2 laser beam
Laser specifications
According to EN 60825-1:1994+A2:2001+A1:2002
Laser class 2
λ 650 nm P: ≤ 1 mW
10
230 V ~ 50 Hz
IP 20
120 W/P1 (S2/5 min)
-1
400-1,600 per min
128/133 mm
50 mm
20 mm
2 m
93 dB
650 nm
<1 mW
610x270x390 mm
17 kg
In such a case, Idle running
the user must
take anti-noise
measures (ear
protectors to be
used).
82.6 dB 72.2 dB
92.4 dB 81.8 dB
RLM-08