Preparation; Trial Operation - Güde GF 180 Mode D'emploi

Manual or recommended by the manufacturer of the
device. Use of different devices or accessories than
recommended in the Manual or in catalogue may
cause accident.
•
Repairs should be made only by an authorized
customer´s service
Thie electric device complies with the relevant safety
regulations. The repairs should be made only by an
authorized customer´s service, otherwise the
accidents may occur.
3

Preparation

Safety work with the device is possible only after you have
carefully read the Manual and Safety regulations and if you
strictly observe the instructions therein. Before putting into
operation check if the voltage on the type label correponds
with the mains voltage and if the device is furnished with a
correct plug. The devices marked with 230 V can be also
connected to 220 V. The connection to the mains can be
made only with sockets with protection contact, with
protection conductor installed according to the regulations.
The works connected with the reconstruction of the device
and the maintenance works can be performed on the
device only if the device is disconnected from the mains.
4
Diamomd Dividing Wheel
The clean cutting is only possible when only diamond
dividing wheels that are sharp and suitable for material to
be treated are used. The diamond dividing wheel supplied
together with the device is designated for cutting the tiles.
Only diamond dividing wheels with 180 mm dia may be
used with this cutting device. Please make sure that
maximum revolution number of the diamond dividing wheel
is higher than maximum number of revolutions of the
device. Diamond dividing wheels whose basic body is
thicker or whose cutting width is smaller than the thickness
of the spliting wedge shall not be used.
Do not use diamond dividing wheels that are distorted
or damaged with crack fissures or damaged in another
way!
Note that after approx. 2-3 cutting processes the
diamond dividing wheel is losing its possible out-of-
balance !!
5
Replacement of the Diamond Dividing
Wheel (Fig. E)
Make sure the plug is pulled out and the cutting device is
off.
1. Remove the vessel for water that can be hanged out
by lifting therof.
2. Use screwdriver* and remove the bottom protection
(h).
3. Use the key* for releasing the nut (g).
4. Remove outer flange (f) and take off the diamond
dividing wheel (e). Put the new wheel on the internal
flange (f), use correct direction of rotation, assemble
the new flange (f), and tighten throughly the nut (g).
Make sure the diamond dividing wheel (e) is correctly
centred.
5. Fasten the bottom protection (h) with screws that are
available here.
6. Hang the vessel for water (i).
*(not involved in the delivery scope)
6

Trial Operation

Secure the cutting device with the assembled diamond
dividing wheel and let it run for approx. 30 seconds. After
the switching off the wheel will run down for approx. 10
seconds.
7
Setting of the Splitting Wedge (Fig. C)
The splitting wedge (a) shall always be used. It prevents
jamming of the diamond dividing wheel (e) during
longitudinal cuts. Only original splitting wedges approved
by the Manufacturer may be used. If necessary set the
splitting weedge according to the figure.
1. Loosen the fixing screws (b).
2. Set the splitting wedge (a) according to the figure, the
splitting wedge shall be set centrally to the diamond
dividing wheel.
3. Fasten again the fixing screws (b).
8
Setting the Cutting Angle (Fig. D)
Loosen the tommy screw (c) on both sides, set the cutting
angle according to the scale and fasten duly the tommy
screw (c) again.
0° : Rectangular cut
45°: cut with 45° angle
9
Filling and Check of the Vessel for Water
Pour a lot of water into the vessel prepared for this
purpose, till the diamond dividing wheel is immersed in the
water up to approx. 1 cm. The vessel can be removed from
the device when filling the water. The water level shall be
checked regularly in order to prevent excessive dust
generation.
Caution: Sufficient quantity of water should always be
used for getting optimum cutting reults and for
maintaining the wear due to cutting as low as
possible.
10
Operation Instructions
•
Make sure the workpiece to be treated is duly
secured and cannot be thrown away from this
position. Use shifting bar or shifting pin.
•
Use suitable diamond dividing wheeel for every
material.
•
Shift the workpiece to the running diamond dividing
wheel. Make sure the shifting is even.
•
Protective cover shall always be used and shall
never be jammed.
•
The protective cover will open automatically by the
workpiece.
•
The top and the bottom of the cutting track shall be
free of any obstacles.
•
Diamond dividing wheels shall not be braked by side
pressure on the body. Should the diamond dividing
wheel be blocked, switch the device immediately off.
•
Pull out the plug out of the socket before putting the
device out of operation, during the breaks and when
the device is not used.
11
Use of the Rabbet (Fig. F)
Parallel rabbet (r) and rabbet for cutting on mitre (o) make
it possible to perform parallel and tapered cuttings. Loosen
the tommy screw (p), put the rabbet into the guideway and
set the required size. Tighten the tommy screws (p) again.
The scale (k) serves for setting the parallelity.
(The Figure is just symbolic, it may differ from the real
execution of the device.)