Publicité
Les langues disponibles
Les langues disponibles
Use protective glasses and a respirator
Use always protective glasses, and a respirator at
works where dust is generated.
Protective cover
Keep the protective cover over the diamond dividing
wheel always on place.
Do not use cable for other purposes
Do not carry the device by means of cable and do not
use cable when pulling it out of the socket. Protect
the cable against heat, oil and sharp edges.
Secure the workpiece
Place the workpiece by means of sliding bar or sliding
pin to the running diamond dividing wheel. Make sure
ther shift is even.
Do not leave the field designated for standing
Avoid abnormal posture. Care for due posture and
keep balance when working.
Maintain your device with care.
Keep your device always clean. Observe the
regulations for maintenance and replacement of the
device. Check regularly plug and cable and in case
they are damaged, have them replaced by an
authorized specialist. Check regularly the extension
cable and replace it if it is damaged. Clean carefully
the working table after every use and protect it
against corrosion by wiping it with a dry cloth slightly
soaked with oil.
Pull out the plug
If the device is not used, pull out the plug before
starting maintenance and when replacing diamand
dividing wheel.
Do not leave the tool keys in the lock
Before switching on make sure that the tool keys and
setting tools are removed..
Extension cables in the outside environment
In the outside environment use only extension cables
approved for such use and marked in corresponding
way.
Check if your device is not damaged
Before further use of the device check carefully
protective equipments or slightly damaged
components if their function is faultless and if it is in
compliance with their purpose.
Check if the moving parts function is all right, it these
parts are not jammed or if they are not damaged.
All parts should be correctly assembled and all
conditions should be fulfilled so that the fultless
operation of the device would be waranteed. Faulty
equipment and damaged parts shall be due repaired
or replaced by the customer´s service, unless
otherwise is stipulated in the Manual. The damaged
switches shall be replaced by the customer´s service.
Do not use devices at which the switch cannot be
switched on and off.
Blunt dividing wheels shall be replaced in time, the
electric equipment shall be only repaired by the
electrician-specialist
Pay always attention
Folow your work. Proceed sensibly. Do not use the
device if you are not properly concentrated.
Caution!
It is in the interest of your personal safety to use only
accessories and additional devices mentioned in the
Manual or recommended by the manufacturer of the
device. Use of different devices or accessories than
recommended in the Manual or in catalogue may
cause accident.
Repairs should be made only by an authorized
customer´s service
Thie electric device complies with the relevant safety
regulations. The repairs should be made only by an
authorized customer´s service, otherwise the
accidents may occur.
Preparation
Safety work with the device is possible only after you have
carefully read the Manual and Safety regulations and if you
strictly observe the instructions therein. Before putting into
operation check if the voltage on the type label correponds
with the mains voltage and if the device is furnished with a
correct plug. The devices marked with 230 V can be also
connected to 220 V. The connection to the mains can be
made only with sockets with protection contact, with
protection conductor installed according to the regulations.
The works connected with the reconstruction of the device
and the maintenance works can be performed on the
device only if the device is disconnected from the mains.
Diamomd Dividing Wheel
The clean cutting is only possible when only diamond
dividing wheels that are sharp and suitable for material to
be treated are used. The diamond dividing wheel supplied
together with the device is designated for cutting the tiles.
Only diamond dividing wheels with 180 mm dia may be
used with this cutting device. Please make sure that
maximum revolution number of the diamond dividing wheel
is higher than maximum number of revolutions of the
device. Diamond dividing wheels whose basic body is
thicker or whose cutting width is smaller than the thickness
of the spliting wedge shall not be used.
Do not use diamond dividing wheels that are distorted
or damaged with crack fissures or damaged in another
way!
Note that after approx. 2-3 cutting processes the
diamond dividing wheel is losing its possible out-of-
balance !!
Replacement of the Diamond Dividing Wheel (Fig. E)
Make sure the plug is pulled out and the cutting device is
off.
1.
Remove the vessel for water that can be hanged out
by lifting therof.
2.
Use screwdriver* and remove the bottom protection
(h).
3.
Use the key* for releasing the nut (g).
4.
Remove outer flange (f) and take off the diamond
dividing wheel (e). Put the new wheel on the internal
flange (f), use correct direction of rotation, assemble
the new flange (f), and tighten throughly the nut (g).
Make sure the diamond dividing wheel (e) is correctly
centred.
5.
Fasten the bottom protection (h) with screws that are
available here.
6.
Hang the vessel for water (i).
*(not involved in the delivery scope)
Trial Operation
Secure the cutting device with the assembled diamond
dividing wheel and let it run for approx. 30 seconds. After
the switching off the wheel will run down for approx. 10
seconds.
Setting of the Splitting Wedge (Fig. C)
The splitting wedge (a) shall always be used. It prevents
jamming of the diamond dividing wheel (e) during
longitudinal cuts. Only original splitting wedges approved
Publicité
