Configuration; Generator Use; Important; Technical Data - Migatronic Automig 183 Manuel D'instruction

Configuration

MIGATRONIC disclaims all responsibility for
damaged cables and other damages related to
welding with under sized welding torch and
welding cables measured by welding
specifications e.g. in relation to permissible
load.

Generator use

This welding machine can be used at all mains
supplies providing sine-shaped current and
voltage and not exceeding the approved
voltage tolerances stated in the technical data.
Motorised generators observing the above can
be used as mains supply. Consult your supplier
of generator prior to connecting your welding
machine. MIGATRONIC recommends use of a
generator with electronic regulator and supply
of minimum 1.5 x the maximum kVA
consumption of the welding machine. The
guarantee does not cover damage caused by
incorrect or poor mains supply.

Important!

In order to avoid destruction
of plugs and cables, good
electric contact is required
when connecting earth
cable and welding torch to
the machine.
Connection of gas bottle
Use only gas bottles with a max. height of 100
cm. If larger bottles are used the machine may
tip over.
Adjustment of wire brake
The wire brake must ensure that the wire reel
brakes sufficiently quickly when welding stops.
The required brake force is depending on the
weight of the wire reel and the maximum wire
feed speed. A brake torque of 1.5-2.0 Nm will
be satisfactory for most applications.
Adjustment:
- Dismount the control
knob by placing a thin
screw driver behind
the knob and
thereafter pull it out
- Adjust the wire brake
by fastening or
loosening the self-
locking nut on the axle
of the wire hub
- Remount the knob by pressing it back into the
groove

TECHNICAL DATA

We reserve the right to changes
Type
Automig 183
Current range 20-180 A
Voltage adjustment 7
Duty cycle, 100% 65 A
Duty cycle, 60% 85 A
Duty cycle, 35% 110 A
Open circuit voltage 14-30 V
1
Mains voltage 400 V
Fuse 230V/400V 10 A/10 A
Mains current, effective 2.5 A
Mains current, max. 5.7 A
Consumption, 100% 1.8 kVA
Consumption, open circuit <10 W
Power factor 0.85
Wire dimension 0.6-1.0 mm
Wire reel capacity 5-15 kg
Wire speed 2-12 m/min
2
Spot welding time 0.15-2.5 secs
2
Stitch welding time 0.15-2.5 secs
Burn-back 0.05-0.5 secs
3
Application class S
4
Protection class IP21
Standards
Dimensions, lxwxh 72x38x70 cm
Weight 57 kg
Dispose of the product according to
local standards and regulations.
www.migatronic.com/goto/weee
1
Delivery for other mains voltages is possible
2
The functions 4-times, spot and stitch welding can only be found
on some machine versions
3
Meets the demands made for machines which are to operate
under special working conditions
4
This machine is designed for indoor operation and meets the
requirements of protection class IP21.
20
Automig 223
Automig 273
20-200 A 20-250 A
10 10
105 A 140 A
125 A 165 A
150 A 200 A
14-30 V 15-34 V
400 V 400 V
10 A/10 A 10 A/10 A
4.0 A 5.9 A
7.3 A 10,0 A
2.8 kVA 4.1 kVA
<10 W <10 W
0.85 0.85
0.6-1.2 mm 0.6-1.2 mm
5-15 kg 5-15 kg
2-14 m/min 2-15 m/min
0.15-2.5 secs 0.15-2.5 secs
0.15-2.5 secs 0.15-2.5 secs
0.05-0.5 secs 0.05-0.5 secs
S S
IP21 IP21
EN/IEC60974-1
EN/IEC60974-5
EN/IEC60974-10
72x38x70 cm 72x38x70 cm
64 kg 66 kg