Publicité
1. Introduction
These operating instructions are intended to make it easier
for you to become familiarised with the machine and use its
capabilities in the proper manner. The operating instructions
contain important information on operating the machine in
a safe, proper and cost effective manner. Following them will
help to avoid hazards, repair costs and down times, enhance
reliability and prolong service life.
Existing national regulations on preventing accidents and on
protecting the environment are also applicable.
The machine will only be assembled and installed by
persons instructed to do so by Paul Hettich GmbH & Co.
KG. This also applies in particular to starting it up for the
first time.
The operating instructions must be available at the machine
all the time. The operating instructions must be read and
applied by any person entrusted with working with / on the
machine, e.g.:
·
Operation
·
including setting up, troubleshooting while working,
disposal of production waste, care, disposing of
consumables and auxiliary substances,
Maintenance
·
·
· Servicing, inspection, repair and
Transportation.
·
74
1.1 Rating plate
The rating plate shows the following information:
Manufacturer
Address
Type designation, machine numbers
System number
Year of manufacture
Technical specifications (e.g. nominal pressure)
State all of the above details when requesting technical
information and ordering replacement parts.
Reprinting, even in part, is only permissible with the consent
of Hettich Maschinentechnik GmbH & Co. KG.
1.2 Information for the owner
In addition to these operating instructions and the accident
prevention regulations in force in the country of use or at
the place of application, it is also necessary to follow the
recognised code of safe and proper working practice.
Without the consent of Paul Hettich GmbH & Co. KG, the
machine owner must not make any additions, alterations or
modifications to the machine that may affect safety.
Replacement parts used must meet the technical requirements
defined by Hettich Maschinentechnik GmbH & Co. KG.
This is always ensured when using genuine replacement parts
from the applicable replacement parts list.
Only ever deploy trained or instructed personnel and clearly
define personnel responsibilities with regard to operating,
servicing and repair.
2. General
2.1 Intended use
Fig. 1: Drawer assembly jig
Warning
Warning!
The machine must only be used in for its inten-
ded purpose and be in a perfectly safe condition.
Operating safety is only guaranteed if the machi-
ne is used for its intended purpose.
The ArciFit 300 / InnoFit 300 drawer assembly jig
for manually assembling drawer systems has been designed
for ArciTech / InnoTech.
All system related sizes, between maximum and minimum
dimensions, can be set. The dimensions specified are key
dimensions which can be set using fixed stops.
Operating modes: manual operation
Personnel required: 1 operator
Any other use beyond this is deemed to be improper and non
intended use.
Intended use also includes following the operating, servicing
and maintenance conditions prescribed by the manufacturer.
Unauthorised changes to the machine will result in the loss of
product liability and liability on the part of the manufacturer
for resultant damage.
Any other use beyond this is deemed to be non intended use.
The manufacturer shall not be liable for any damage this
causes, with the risk involved being borne solely by the user.
2.2 Foreseeable incorrect use
Warning
Hazards may occur if the system is used
incorrectly!
The following situations in particular are
deemed to be foreseeable hazardous situa-
tions:
· Persons possibly manipulating safety guards.
Persons possibly removing separating pro-
tective guards and then putting the machine
into operation.
· Service personnel possibly working on pressu-
rised parts in spite of them not being depressu-
rised beforehand.
· Service personnel possibly leaving tools inside
the system and returning it to operation after
completing servicing work.
· Service personnel possibly working on the ma-
chine (e.g. troubleshooting, servicing) despite
the machine being in operation.
The situations above describe some of the residual hazards
which, despite being impermissible, may occur and harm the
health of staff.
The owner must observe the safety requirements defined in
the German Ordinance on Industrial Safety and Health
(Betriebssicherheitsverordnung).
75
Publicité
Chapitres
Dépannage
