Publicité
Drive
Electric motor
Nominal consumption P1 kW
Power output P2
kW
Motor speed
rpm.
Operating mode
Nominal current
Pre-scorer
Nominal consumption P1
Power output P2
Technical changes reserved!
Noise data
Measuring conditions as per DIN EN ISO 11202;
DIN EN ISO 3746; DIN ISO 7960
The stipulated values are emission values and so do
not necessarily represent safe working values.
Although there is a correlation between emission lev-
els and exposure levels, it is not possible to reliably
determine whether additional precautionary meas-
ures will be required or not based on this. Factors
that could influence the exposure level present at any
given time in the work area include the duration of
exposure, the nature of the working area, other noise
sources etc. e.g. the number of machines and neigh-
bouring processes. The permissible workstation val-
ues can also vary from country to country. However,
this information should enable the operator to better
evaluate the hazards and risks.
Sound power level in dB
Idle L
=
WA
Working L
=
WA
Sound pressure level at workstation in dB
Idle L
=
pAeq
Working L
=
pAeq
A measurement uncertainty supplement K = 4 dB ap-
plies to the emissions values stated.
Dust emission details
The dust emission values measured according to the
"Principles for Testing Dust Emission (Concentration
Parameters) of Woodworking Machines" of the Ger-
man Expert Committee on Wood are below 2 mg/m
Thus, when the machine is connected to a proper op-
erational extraction system with an air velocity of at
least 20 m/s, it can be assumed that the TRK limit val-
ue for wood dust applicable in the Federal Republic of
Germany will be safely complied with in the long term.
30 | GB
230V
400V
50 Hz
50 Hz
3,0
4,8
2,2
4,0
2800
2800
S6/40%
S6/40%
11.6 A
8.2 A
kW
0,8
kW
0,5
97.5 dB(A),
100.4 dB(A)
86.7 dB(A),
87.1 dB(A)
.
3
www.scheppach.com
9. Unpacking
Note:
• Familiarise yourself with the product by means of
the operating instructions before using for the first
time.
• With accessories as well as wearing parts and
replacement parts use only original Scheppach
parts. Replacement parts can be obtained from
your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of
the warranty period.
• Familiarise yourself with the product by means of
the operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
product.
m WARNING!
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
10. Assembly /
Before commissioning
m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Assembly
All installation and refitting work may only be carried
out with the mains plug removed.
Your Scheppach circular table saw is not completely
assembled for packaging reasons.
Assembly tool
The scope of delivery includes
1 open-end spanner
19 mm Width across flats
1 open-end spanner
30 mm Width across flats
1 Allen key
5 mm Width across flats
Publicité
