Publicité
CARE & USE
Safety Tips
• Before opening gas cylinder valve, check the regulator for tightness.
• When appliance is not in use, turn off all control knobs and gas.
• Use long-handled plancha utensils and oven mitts to avoid burns and
splatters. Use protective gloves when handling hot components.
• Maximum load for hot plate, if equipped, and side shelf is 4.5 Kg.
Cooking vessel minimum dia 200mm and maximum dia. 260 mm.
NOTE: Your plancha may NOT be equipped with a Hot plate!
• Use long-handled plancha utensils and oven mitts to avoid burns and
splatters. Use protective gloves when handling hot components.
• Be very careful when children, the elderly, or pets are nearby.
• If you notice grease or other hot material dripping from appliance onto
valve, hose or regulator, turn off gas supply at once. Determine the
cause, correct it, then clean and inspect valve, hose, and regulator
before continuing. Perform a leak test.
• Do not store objects or materials inside the appliance cart enclosure
that would block the flow of combustion air to the underside of either
the control panel or the firebox bowl.
• DO NOT disconnect or change gas container within 3m of an open
flame or other ignition source.
Cylinder Placement
Cylinders placed in the appliance shall have a maximum diameter of
330mm and maximum height, including regulator, of 450mm. Larger
cylinders are to be placed under side shelf or behind the plancha only.
Cylinders placed on the ground shall not be placed under the hot plate.
Regulator Requirements
A regulator must be used with this appliance. Use only gas regulator
supplied with your barbeque. If a regulator is not supplied then use only
regulator certified according to EN16129 (Flow rate max. 1.5 kg/h) and
approved for your country and gas specified in Technical Data.
Hose Requirements
Use only approved hose which is certified to appropriate EN standard
and does not exceed 1.5m length. For Finland, the hose length shall
not exceed 1.2m.Before each use, check to see if hoses are cut or worn.
Make sure hose is not kinked. Replace damaged hoses before using
appliance. Replace hose as required by national requirements.
Ignitor Lighting
• Do not lean over plancha while lighting.
• When appliance is not in use, turn OFF all control knobs and gas.
1. Turn gas burner control valves to OFF.
2. Open lid during lighting or re-lighting.
3. Turn ON gas at LP cylinder.
4. To ignite, push and turn burner knob to HIGH. Immediately, push
and hold ELECTRONIC IGNITOR button until the burner lights.
5. If ignition does NOT occur in 5 seconds, turn the burner controls
OFF, wait 5 minutes and repeat the lighting procedure.
6. Repeat steps 4 and 5 to light other main burners.
WARNING
• Turn controls and gas cylinder off when not in use.
• Make sure that when connected hose does not touch any warm
surfaces.
If ignition does NOT occur in 5 seconds, turn the burner controls
OFF, wait 5 minutes and repeat the lighting procedure. If the burner
does not ignite with the valve open, gas will continue to flow out of
the burner and could accidently ignite with risk of injury.
Match Lighting
• Do not lean over plancha while lighting.
• When appliance is not in use, turn OFF all control knobs and gas.
1. Turn gas burner control valves to OFF.
2. Open lid during lighting or re-lighting.
3. Turn ON gas at LP cylinder.
4. Place match into match holder (hanging from back panel of
plancha). Light match; then light burner by placing match through
the gap under plancha. Immediately push in and turn burner knob
to the  HIGH position. Be sure burner lights and stays lit.
5. Light adjacent burners in sequence by pushing knobs in and turning
to the HIGH position.
Leak Testing Valves, Hose and Regulator
Leak test before first use, at least once a year, and every time the
cylinder is changed or disconnected.
1. Turn all appliance control knobs to OFF.
2. Be sure regulator is tightly connected to gas cylinder.
3. Turn on Gas. If you hear a rushing sound, turn gas off immediately.
There is a major leak at the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and half water) onto hose
connections.
5. If growing bubbles appear, there is a leak. Turn off gas at cylinder
immediately and check tightness of connections. If leak cannot be
stopped do not try to repair. Call for replacement parts.
6. Always turn off gas at cylinder after performing leak test.
GB
4
CAUTION
C H AR BR O I L . EU
Publicité
