Publicité
Draining fresh water
ATTENTION
Cleaning solution in the fresh water tank
Damage to fresh water tank, valves and seals
Never leave the cleaning solution in the fresh water tank at
the end of operation.
1. Remove the fresh water drain hose from the holder and
lower it over a suitable collecting device.
2. Drain the cleaning solution.
3. Remove the fresh water tank cap.
4. Rinse the fresh water tank with clear water (maximum 60 °C).
Shutting down the device
1. Turn the program switch to "OFF".
2. Remove the Intelligent Key.
3. Secure the device against rolling away.
4. Charge the batteries if necessary.
Gray intelligent key
The gray Intelligent Key grants the supervisory staff ex-
tended authorizations and setting options.
1. Insert the Intelligent Key.
2. Select the desired function by turning the info button.
Transport travel
1. Set the program selector switch to "Transport travel".
2. Press the Info button.
The following settings can be made in the Transport travel
menu:
● Resetting the maintenance counter
● Resetting the day counter
● Key management
● Choosing the brush shape
● After-running time
● Standard setting
● Setting the language
● Switch menu
● Travel speed
● Factory setting
● Activating the manual tank rinsing gun
Resetting the maintenance counter
If maintenance work shown in the display has been carried
out, the corresponding maintenance counter must then be
reset.
1. Turn the info button until "Maintenance counter" is dis-
played.
2. Press the info button.
The meter readings are displayed.
3. Rotate the info button until the counter to be deleted is
highlighted.
4. Press the info button.
5. Select "Yes" by rotating the info button.
6. Press the info button.
The counter is deleted.
Note
The service counter can only be reset by Customer Ser-
vice staff.
The service counter shows the time until the next service
due by Customer Service.
20
1. Turn the Info button until "Counter" is displayed.
This menu shows the total operating hours and the day
counter.
Delete the day counter:
2. Press the Info button.
The "Delete counter" menu is displayed.
3. Turn the Info button until "Day counter" is highlighted.
4. Press the Info button.
The authorizations are assigned for each yellow Intelligent
Key used and the language of the display is set for this In-
telligent Key in the "Key menu" menu item.
1. Insert the gray Intelligent Key.
2. Turn the info button until the menu item "Key menu" ap-
pears in the display.
3. Press the info button.
4. Remove the gray Intelligent Key and insert the yellow or
white Intelligent Key to be personalized.
5. Select the menu item to be changed by turning the info
button.
6. Press the info button.
7. Select the setting of the menu item by turning the info button.
8. Confirm the setting by pressing the menu item.
9. Select the next menu item to be changed by turning the
info button.
10.After all settings have been made, call up the menu
"Save?" by turning the info button.
11.Press the info button.
The authorizations are saved.
The "Continue key menu" display appears.
● Yes: Program another Intelligent Key
● No: Exit the key menu
12.Press the Info button.
Choosing the brush shape
This function is required when changing the cleaning head.
1. Turn the info button until the menu item "Brush head" is
shown in the display.
2. Press the info button.
3. Turn the info button until the desired brush shape is
highlighted.
4. Press the Info button.
5. To change the cleaning head, move the lifting drive by
turning the info button:
"Up": Lift
"Down": Lower
"OFF": Stop
6. Turn the info button until the "OFF" menu item is dis-
played.
7. Press the Info button.
The menu is exited.
The controller performs a restart.
1. Turn the info button until the menu item "After-running
time" is shown in the display.
2. Press the info button.
3. Turn the info button until the desired function is high-
lighted.
4. Press the Info button.
5. Turn the info button until the desired after-running time
is displayed.
6. Press the Info button.
English
Resetting the counter
Key management
After-running time
Publicité
