Publicité
Les langues disponibles
Les langues disponibles
Filling with detergent
Filling the detergent into the fresh water tank
Note
First fill water into the detergent tank, then add the appro-
priate dosage of detergent to the tank. If the detergent is
poured in first, this can lead to strong foaming.
ATTENTION
Danger of clogging
When adding detergent to the fresh water tank, the detergent
can dry out and disrupt the function of the dosing device.
Rinse the device with clear water after adding detergent to
the fresh water tank: Select a cleaning program with water
application, set the water quantity to the highest value, set
the detergent dosage to "0".
Filling detergent with a dosing device (option)
Detergent is added to the fresh water on its way to the
cleaning head by a dosing device.
Note
A maximum of 3% detergent can be added with the dosing
device. For higher dosage, the detergent must be added to
the fresh water tank.
ATTENTION
Danger of clogging
When adding detergent to the fresh water tank, the detergent
can dry out and disrupt the function of the dosing device.
Rinse the device with clear water after adding detergent to
the fresh water tank: Select a cleaning program with water
application, set the water quantity to the highest value, set
the detergent dosage to 0.
1. Place the canister with the detergent in the detergent
tray behind the seat.
2. Unscrew the canister cap.
3. Insert the detergent suction lance of the dosing device
into the canister.
Note
● The device has a fresh water level indicator on the dis-
play. Detergent dosing is stopped when the fresh water
tank is empty. The cleaning head continues to work
without supply of liquid.
● Detergent addition is also stopped when the detergent
canister is empty. A notice symbol appears on the dis-
play. Only fresh water is fed to the cleaning head.
Adjusting parameters (yellow Intelligent key)
The parameters for the various cleaning programs are pre-
set in the device.
Individual parameters can be changed depending on the
authorization of the yellow Intelligent Key.
The modified parameters only remain in effect until a differ-
ent cleaning program is selected with the program switch.
A gray Intelligent Key must be used for making adjust-
ments if parameters are to be changed permanently. This
adjustment procedure is described in the section "Gray In-
telligent Key".
Note
R cleaning head only: Almost all displayed texts regarding
parameter settings are self-explanatory. If you need more
detailed information about the parameters, please contact
the Customer Service.
18
● Fine Clean: Low brush speed for removing gray film
from fine stone.
● Whisper Clean: Medium brush speed for maintenance
cleaning with reduced noise level.
● Power Clean: High brush speed for polishing, crystalliz-
ing and sweeping.
1. Set the program switch to the desired cleaning program.
2. Press the Info button.
3. Turn the Info button until the desired parameter is dis-
played.
4. Press the Info button.
The set value flashes.
5. Set the desired value by turning the Info button.
6. Confirm the changed setting by pressing the Info button
or wait until the set value is automatically accepted after
10 seconds.
Adjusting the suction bar
The suction bar only needs to be readjusted in special cas-
es. The factory setting is suitable for most applications.
Sweeping (Combo variant only)
The sweeping mechanism picks up loose dirt before per-
forming floor cleaning.
WARNING
Moving parts
Danger of injury
Note that the suction turbine, side brushes and filter de-
dusting run on after switching off.
ATTENTION
Improper use of the device when sweeping
Risk of damage to the sweeping mechanism.
Do not sweep up packing tape, wires or similar.
Only drive over steps up to a maximum of 2 cm.
Sweep only dry surfaces to prevent clogging and contam-
ination of the dust filter.
1. Switch on the "Sweeping" switch.
The sweeping mechanism is activated.
The coarse dirt flap can be lifted to sweep up larger objects
(up to approx. 6 cm high).
DANGER
Danger of injury from waste!
Waste can be thrown out when the coarse dirt flap is
opened.
Only lift the coarse dirt flap when there are no persons in
the vicinity.
Note
The sweeping effect and dust suction deteriorate when the
coarse dirt flap is raised. Only lift the coarse dirt flap when
necessary.
1. Operate the pedal to raise the coarse dirt flap.
1. Set the "Sweeping" switch to "0".
The sweeping mechanism is deactivated. After the sweep-
ing operation is finished, the dust filter is cleaned for ap-
prox. 15 seconds.
English
Coarse dirt flap
Finishing sweeping
Publicité
