Publicité
1
Safety-related information
– Before using this product, carefully read these instructions
for use and those of the associated products.
– Strictly follow the instructions for use. The user must fully
understand and strictly observe the instructions. Use the
product only for the purposes specified in the intended use
section of this document.
– Do not dispose of the instructions for use. Ensure that they
are stored and used appropriately by the user.
– Only trained and competent users are permitted to use
this product.
– Do not use a faulty or incomplete product. Do not modify
the product.
– Notify Dräger in the event of any component fault or
failure.
– Comply with all local and national rules and regulations
associated with this product.
– Only trained and competent personnel are permitted to
inspect, repair and service the product. Dräger
recommend a Dräger service contract for all maintenance
activities and that all repairs are carried out by Dräger.
– Use only genuine Dräger spare parts and accessories.
Otherwise, the proper functioning of the product may be
impaired.
2
Conventions in this document
2.1
Meaning of the warning notices
The following warning notices are used in this document to
alert the user to potential hazards. The meanings of the
warning notices are defined as follows:
Warning
Signal word
sign
DANGER
WARNING
CAUTION
NOTICE
2.2
Trademarks
Trademark
Trademark owner
Dräger
®
®
D-mex
, FPS
,
®
HPS
,
®
Panorama Nova
,
®
®
PAS
, PSS
, X-
®
plore
Instructions for use
|
Dräger CPS 7800
Classification of the warning
notice
Indicates an imminently haz-
ardous situation. If not avoided,
it will result in death or serious
injury.
Indicates a potentially hazard-
ous situation. If not avoided, it
could result in death or serious
injury.
Indicates a potentially hazard-
ous situation. If not avoided, it
could result in physical injury. It
may also be used to alert
against unsafe practices.
Indicates a potentially hazard-
ous situation. If not avoided, it
could result in damage to the
product or environment.
Trademark
Trademark owner
Ecolab
®
®
Eltra
, ECOLAB
Dr. Weigert
®
neodisher
KCL GmbH
®
Tricotril
Cryo-LNG™
Tempshield, Inc.
2.3
Abbreviations
Abbreviation
Explanation
FKM
Fluoroelastomer
3
Description
Dräger CPS 7800 are gas-tight chemical protective suits in
line with EN 943-2:2019 (type 1b-ET). They are re-usable.
A compressed air breathing apparatus or a compressed air
hose respirator and a full face mask are required for breathing
air supply. The full face mask can be permanently integrated
into the chemical protective suit and has one of the following
connections:
– Round thread connection (RA) according to DIN EN 148-1
– Plug-in connector (P) for protective positive apparatus
– Universal connector (PE) according to DIN EN 148-3
– Universal plug-in connector (PE/ESA) according to
DIN 58 600
Only use for demand valves that fit the relevant full face
mask. This ensures fault-free operation.
Alternatively, the chemical protective suit can be equipped
with a face cuff. A full face mask that fits the compressed air
breathing apparatus or compressed air hose respirator is
placed on the face cuff. For further information see: "Tested
personal protective equipment", page 26.
The compressed air breathing apparatus or compressed air
hose respirator, full face mask and safety helmet are worn
over the chemical protective suit.
The chemical protective suit is equipped with exchangeable
gloves. There are different glove combinations available:
– inside chemical-resistant FKM/butyl glove, outside
optional cut- and puncture-resistant Tricotril overglove
– inside chemical-resistant laminate glove, outside cut -
resistant and watertight Tricotril glove (glove combination)
– Inside chemical-resistant laminate glove, outside butyl
glove (glove combination)
The chemical protective suit can be equipped either with
socks made from the same material as the suit or with boots.
The socks by themselves do not provide adequate protection
from mechanical stresses. The user must therefore also wear
suitable protective boots which are approved in accordance
with EN ISO 20345. A cuff prevents the penetration of
substances between the socks and safety boots.
The chemical protective suit features a pocket for radio units
and a push-to-talk button flap. The pocket is labelled with the
type ID.
The following optional components can be fitted to the
chemical protective suit:
Safety-related information
|
25
Publicité
