Publicité
EN
FINEFINISH TIPS
Top-quality painting nozzles with optimised properties for particularly high-quality surfaces even in low-pressure areas.
All of the tips in the table below are supplied together with the appropriate gun fi lter.
i
Application
Water and solvent-based varnis-
hes, lacquer paints, oils, separa-
ting agents
Synthetic resin-based paints, PVC
paints, 2-K lacquers
Primers, fi llers
Fireproofi ng paints, corrosion
protection paints
HEA NOZZLES FOR LOW-MIST SPRAYING AT LOW PRESSURE
HEA stands for High Effi ciency Airless, an innovative nozzle technology revolutionising airless spraying. HEA nozzles allow the
pressure of the spray device to be reduced right down and allow it to work in the low-pressure range (ideally at 80 - 140 bar).
The nozzles can be used with all TradeTip 3 nozzle holders and WAGNER devices.
Some paints may need to be diluted to achieve the best result possible. The experts at Wagner application technology have
therefore tested a wide range of materials for you. Their recommendations can be found in the Wagner Spray Guide at sprayguide.
wagner-group.com.
HEA tip table
All of the tips in the table below are supplied together with the appropriate gun fi lter.
i
Application
Synthetic-resin paints
PVC paints
Paints, primers
Fillers
Fillers
Rust protection paints
Set the low pressure in the HEA range
and start.
Rust protection paints
Latex paints
Dispersions
Rust protection paints
Latex paints
Dispersions
Flame retardant
1) Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.
1) Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.
When working with a HEA nozzle, a pressure setting of 50 - 150 bar / 5-15 MPa (area marked in green on the
i
pressure gauge) is recommended.
42
Accessories
Tip marking
Spray
angle
208
20°
308
30°
408
40°
210
20°
310
30°
410
40°
510
50°
212
20°
312
30°
412
40°
512
50°
214
20°
314
30°
414
40°
514
50°
Tip marking
Spray
angle
211
20°
311
30°
411
40°
213
20°
313
30°
413
40°
415
40°
515
50°
Even spray pattern without spray edges.
615
60°
417
40°
517
50°
617
60°
519
50°
619
60°
421
40°
521
50°
621
60°
Bore
Spraying width mm
inch / mm
0.008 / 0.20
120
0.008 / 0.20
150
0.008 / 0.20
190
0.010 / 0.25
120
0.010 / 0.25
150
0.010 / 0.25
190
0.010 / 0.25
225
0.012 / 0.30
120
0.012 / 0.30
150
0.012 / 0.30
190
0.012 / 0.30
225
0.014 / 0.36
120
0.014 / 0.36
150
0.014 / 0.36
190
0.014 / 0.36
225
Bore
Spraying
inch / mm
width mm 1)
0.011 / 0.28
120
0.011 / 0.28
150
0.011 / 0.28
190
0.013 / 0.33
120
0.013 / 0.33
150
0.013 / 0.33
190
0.015 / 0.38
190
0.015 / 0.38
225
If edges are visible, slowly increase the
0.015 / 0.38
270
pressure.
0.017 / 0.43
190
0.017 / 0.43
225
0.017 / 0.43
270
0.019 / 0.48
225
0.019 / 0.48
270
0.021 / 0.53
190
0.021 / 0.53
225
0.021 / 0.53
270
SprayPack 18V
Gun fi lter
Order no.
1)
red
0554208
red
0554308
red
0554408
red
0554210
red
0554310
red
0554410
red
0554510
red
0554212
red
0554312
red
0554412
red
0554512
red
0554214
red
0554314
red
0554414
red
0554514
Gun fi lter
Order no.
red
0554211
red
0554311
red
0554411
red
0554213
red
0554313
red
0554413
yellow
0554415
yellow
0554515
yellow
0554615
white
0554417
white
0554517
white
0554617
white
0554519
white
0554619
white
0554421
white
0554521
white
0554621
Publicité
