Publicité
SprayPack 18V
Coating substance
Caution against dangers that can arise from the
sprayed substance and observe the text and
information on the containers or the specifications
given by the substance manufacturer.
Do not spray any liquid of unknown hazard potential.
Do not use paints or solvents that contain halogenated
hydrocarbons, such as chlorine, bleach, methylene
chloride chloride and trichloroethane. They are not
compatible with aluminium. Ask the supplier of the
coating about the compatibility of the material with
aluminium.
High-pressure hose (safety note)
Attention, danger of injury by injection!
Wear and tear and kinks as well as usage
that is not appropriate to the purpose
Danger
of the device can cause leakages to form
in the high-pressure hose. Liquid can be
injected into the skin through a leakage.
High-pressure hoses must be checked thoroughly before
they are used.
Replace any damaged high-pressure hose immediately.
Never repair defective high-pressure hoses yourself!
Avoid sharp bends and folds: the smallest bending radius
is about 20 cm.
Do not drive over the high-pressure hose. Protect against
sharp objects and edges.
Never pull on the high-pressure hose to move the device.
Do not twist the high-pressure hose.
Do not put the high-pressure hose into solvents. Use only
a wet cloth to wipe down the outside of the hose.
Lay the high-pressure hose in such a way as to ensure
that it cannot be tripped over.
Electrostatic charging of spray guns and the high-
pressure hose is discharged through the high-pressure
hose. For this reason the electric resistance between the
connections of the high-pressure hose must be equal or
lower than 197 kΩ/m (60 kΩ/ft.).
For reasons of function, safety and
i
durability, only use genuine WAGNER
high-pressure hoses and spray nozzles.
For overview see „Spare parts lists".
The risk of damage rises with the age of
i
the high-pressure hose.
Wagner recommends replacing high-
pressure hoses after 6 years.
Positioning device
When working indoors:
Vapors containing solvents may not be
allowed to build up in the area of the
Danger
device. Ensure good ventilation.
When working outdoors:
Vapors containing solvents may not be
allowed to blow toward the unit.
Note the direction of the wind.
Maintenance and repairs
Depressurise the device and remove the
battery before carrying out any work on
the device.
Danger
Cleaning the unit
Danger of short circuit through
penetrating water!
Never spray down the unit with high-
Danger
pressure or high-pressure steam
cleaners.
Cleaning units with solvents
When cleaning the unit with solvents,
the solvent should never be sprayed or
pumped back into a container with a
small opening (bunghole). An explosive
Danger
gas/air mixture can be produced. The
container must be earthed.
Do not use flammable materials for
cleaning purposes.
Earthing of the object
The object to be coated must be earthed.
If liquids collect in the area underneath the
i
outlet valve, this could be due to a leak in
the set of pistons. If operations continue, the
liquid can leak and dirt might get under the
device.
Usabel materials*
•
Interior wall paint (dispersions and latex paint)
•
Water- and solvent-based paints, finishes, primers,
stains
stains, , staining sealers wood sealer-preservatives and
oils
oils.
* Observe the instructions of the paint manufacturer.
Unsuitable materials
•
Materials that contain highly abrasive components,
silicate paint, facade paint, caustic solutions and acidic
coating substances.
•
Flammable materials, materials containing acetone or
cellulose thinner
Field of application
Coating of interior walls, doors, radiators, etc. as well as
small and medium-sized objects outdoors (e.g. garden
fences, garage doors, etc.).
EN
27
Publicité
