Publicité
Les langues disponibles
Les langues disponibles
Safety instructions for battery-
operated devices
Note: Warranty claims will be entertained
only if you use batteries and chargers rec-
ommended by Kärcher.
– Always follow the instructions of the
battery manufacturer and the charger
manufacturer. Please follow the statu-
tory requirements for handling and dis-
posing batteries.
– Never leave the batteries in a dis-
charged state; recharge them as soon
as possible.
– Always keep the batteries clean and dry
to avoid creep currents. Protect the bat-
teries and avoid contact with impurities
such as metal dust.
– Do not place tools or similar items on
the battery. Risk of short-circuit and ex-
plosion.
– Do not work with open flames, generate
sparks or smoke in the vicinity of a bat-
tery or a battery charging room. Danger
of explosion.
– Do not touch hot parts of the machine
such as the drive motor (risk of burns).
– Be careful while handling battery acid.
Follow the respective safety instruc-
tions!
– Used batteries are to be disposed ac-
cording to the EC guideline 91/ 157
EWG in an environment-friendly man-
ner.
Appliances with high emptying
system
DANGER
Risk of injury!
When working on the high emptying
system, completely lift and secure the
waste container.
Perform the safeguarding only from
outside the hazard zone.
Devices with overhead guard
NOTICE
The overhead guard (optional) protects the
driver against larger falling objects. Howev-
er, it does not provide rollover protection!
Check the overhead guard for damage
daily.
If the overhead guard, as well as indi-
vidual elements, should be damaged,
replace the entire overhead guard.
Any modification of the overhead guard
and installation of elements, compo-
nents and assemblies other than those
approved by Kärcher is not permitted
and may limit the function of the over-
head guard.
Safety information concerning the
transport of the appliance
Observe the net weight (transport
weight) of the device during transport
on trailers or vehicles.
To transport the device, unplug the bat-
tery plug and securely fasten the de-
vice.
Safety information concerning
maintenance and care
First switch off the appliance and re-
move the key before performing any
cleaning or maintenance tasks on the
appliance, replacing parts or switching
over to another function.
When performing any service and
maintenance work on devices with a
traction battery, the battery must be dis-
connected from the electrical system of
the device via the battery isolation point
(battery plug).
Always disconnect the battery when
working on the electrics.
To do this, first disconnect the negative
terminal and then the positive terminal.
Reconnection is performed in reverse
sequence. Connect the positive termi-
nal first, then connect the negative ter-
minal.
Do not clean the appliance with a water
hose or high-pressure water jet (danger
of short circuits or other damage).
Maintenance work may only be carried
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety regula-
tions.
Please observe the local safety regula-
tions regarding portable commercially
used appliances.
Always use appropriate gloves while
working on the device.
Function
The sweeper operates using the sweep-
shovel principle.
– The rotating roller brush moves the dirt
directly into the waste container.
– The side brush cleans the corners and
edges of the surface and moves dirt
and debris into the path of the roller
brush.
– The fine dust is sucked in via the dust
filter through the suction blower.
Unloading tips
Danger
Risk of injury, risk of damage!
Observe the weight of the appliance when
you load it!
Weight (without batteries)
Weight (with batteries)
* If upgrade kits are installed, the weight is
respectively higher.
Do not use a forklift.
Use a suitable ramp or a crane to load
the appliance!
Observe when using a ramp:
Ground clearance 70 mm.
If the machine is delivered on a pallet,
you must create an unloading ramp us-
ing the boards provided.
You will find the instructions for this pro-
cedure on page 2 (inside of cover).
Important instruction: every board
must be attached with at least 2 screws.
3
-
EN
750 kg*
1200 kg*
17
Publicité
