Korg EFGSJ 4 Manuel D'utilisation page 12

C1 Air is in Piano Song Mode, Sound Demo Song
Mode or Function Mode.
2. Press the Play/Pause button during playback to pause
it.
The Play/Pause button blinks.
3. To resume playback from the point where it was
paused, press the Play/Pause button again.
The Play/Pause button lights up.
Returning to the Beginning of the Song
1. Press the Stop button during playback to stop playing
back the performance.
2. Press the Play/Pause button to start playing back the
song from the beginning.
Skipping to a Specific Measure
1. While the song is playing, stopped or paused, press
the DISPLAY button; the MEASURE LED in the dis-
play lights up.
The current measure appears in the display.
2. Press the + or – button to move to a specific measure.
If playback was stopped, it will be paused (the Play/
Pause button blinks) after moving to the specific mea-
sure. Pressing the Play/Pause button will start playback
from that point.
To quickly return to the first measure (001), simultane-
ously press the + and – buttons.
Changing the Playback Tempo
Press the DISPLAY button, and then, after the TEMPO
LED is lit, press the + or – button to change the tempo.
The setting continues to change while the button is held
down.
To restore the tempo to the original setting, simultaneously
press the + and – buttons.
Playing the Right- and Left-hand Parts Separately
As with Piano Songs, one part can be muted while the other
is played back. Refer to "Practicing a performance" on page
6.
Deleting a Recorded Performance
Each part of a recorded performance can be deleted.
1. Press the FUNCTION button, then the ORGAN2 but-
ton.
2. Press the + or – button to select the part to be deleted,
and then press the Play/Pause button to delete the
part.
3. After the part is deleted, press the FUNCTION button
again.
(Refer to "Function Mode" on page 12" and the "List
of functions" on page 13".)
12
Other functions
Function Mode
The pitch as well as temperament settings etc. can be speci-
fied from the Function Mode. For the functions that can be
set, refer to the "List of functions" below.
In Partner Mode, no settings other than the volume bal-
ance for Partner Mode can be specified.
Adjusting Parameter Settings in the Function Mode
1. Press the FUNCTION button.
The FUNCTION button and the PIANO1 button will
light.
2. Press the appropriate button shown below to select a
parameter.
The pressed button lights up, and the current setting ap-
pears in the display.
Minimum remaining space for recording
Part volume
Temperament
Pitch
Octave of
layer mode
Pedal of
Stereo sound optimizer
layer mode
Delete part of User Song
3. Press the + or – button to select a setting.
To restore the default setting, simultaneously press the +
and – buttons.
The procedures for checking the amount of record-
ing space remaining, for changing a layer octave
and for saving parameter settings differ slightly.
4. To exit Function Mode, press the FUNCTION button.
The FUNCTION button goes dark.
The setting for the auto power off function is saved
when it is changed.
Normally, when the C1/C1 Air is turned off, all param-
eters return to their factory default settings. However,
by performing the "Save parameter settings" (see page
13) operation before the C1/C1 Air is turned off, the
settings specified for the pitch and part volume balance
before the C1/C1 Air was turned off can be saved as the
default settings.
Functions for Piano Song Mode
In Piano Song Mode, the FUNCTION button can be used to
specify the muting level for each part of a Piano Song. The
specified muting level is the same for both Part 1 and Part 2.
1. Press the FUNCTION button; the current muting lev-
el appears in the display.
The FUNCTION button lights up.
2. Press the + or – button to select a setting.
When muted with a setting of 0, there will be no sound,
and with a setting of 12, the sound will be at full vol-
ume.
To restore the default setting (0), simultaneously press
the + and – buttons.
3. After specifying the desired setting, press the FUNC-
TION button.
The FUNCTION button goes dark.
Volume balance
Save parameter
of layer mode
settings
Auto power off