Operating Elements And Connections; Remote Control; Safety Notes - Monacor TFT-1904LED Mode D'emploi

LCD Monitor
These operating instructions are intended for
users without any specific technical knowledge.
Please read the instructions carefully prior to
operation and keep them for later reference.
All operating elements and connections de-
scribed can be found on the fold-out page 3.
1 Operating Elements
and Connections
1.1 Front side of monitor
1 Power LED
does not light up: monitor in stand-by mode
shows green: monitor switched on
shows red: video signal is missing
2 Infrared sensor for the remote control signals
1.2 Rear side of monitor (without base)
3 Button "SOURCE"
– to select the sources:*
AV 1 AV 2 S-Video PC DVI
– as a return button within the on-screen
menu and to deactivate the on-screen
menu
4 Button "MENU" to call the on-screen menu, to
activate a submenu or a menu item and to
confirm menu settings
5 Button "ITEM" to directly set video parame-
ters, i. e. without calling the on-screen menu
and to adjust the volume
First select the parameter with the button:
Brightness Saturation Hue Sharpness
R Gain G Gain B Gain Contrast
or
Contrast Audio Volume Brightness
Then adjust the value of the parameter with
the arrow key or (6 or 25).
6 Arrow keys and
a) as an upward and downward button to
navigate in the on-screen menu (selection
of submenus / menu items / setting options)
b) to increase or to decrease values for video
and audio parameters
c) to increase or to decrease the volume
(keep the respective button pressed)
d) to shortly insert information about the
source (button only)
7 Button to set the monitor to stand-by mode
or to switch it on
8 Power supply jack for connection of the power
supply unit provided
9 USB port (jack type A), it only serves for soft-
ware updates
10 HDMI TM input (jack type A)
11 DVI input (DVI-D jack)
12 VGA input (Sub D jack)
13 S-Video input "Y/ C IN" (mini DIN jack)
14 Composite video input "VIDEO1 IN" (BNC jack)
15 Feed-through output "VIDEO1 OUT (BNC jack)
for the signal at the input "VIDEO1 IN" (14)
16 Composite video input "VIDEO2 IN" (BNC jack)
17 Feed-through output "VIDEO2 OUT (BNC jack)
for the signal at the input "VIDEO2 IN" (16)
* Important note: When switching over a source, wait for at least 3 seconds before you press a button again to prevent
malfunctions.
18 Feed-trough output "AUDIO1 OUT" (RCA jack)
for the signal at the input "AUDIO1 IN" (19)
19 Audio input "AUDIO1 IN" (RCA jack) for con-
nection to the audio output of the source con-
nected to the input "VIDEO1 IN" (14)
20 Feed-through output "AUDIO2 OUT" (RCA
jack) for the signal at the input "AUDIO2 IN"
(21)
21 Audio input "AUDIO2 IN" (RCA jack) for con-
nection to the audio output of the source con-
nected to the input "VIDEO2 IN" (16) or to the
input "Y/ C IN" (13)
22 Audio input "PC AUDIO IN" (3.5 mm jack) for
connection to the audio output of the source
connected to the DVI input (11) or to the VGA
input (12)
chapter 7

1.3 Remote control

23 Button "Mute"
the sound
24 Buttons for fast selection of the sources*
Button "PC / HD" (PC
To select the VGA input (12), the DVI input
(11) or the HDMI
HD
Button "AV1/AV2" (AV 1 AV 2)
To select the input "VIDEO1 IN" (14) or
"VIDEO2 IN" (16)
Button "SV" (S-Video)
To select the input "Y/ C IN" (13)
25 Buttons "Select"
a) as an upward and downward button to nav-
igate in the on-screen menu (selection of
submenus / menu items / setting options)
b) to increase or to decrease values for video
and audio parameters
Audio Volume
c) to increase or to decrease the volume
26 Button "Freeze" to activate and to deactivate
the "Freeze" function (still picture)
(source PC)
– not possible for DVI and HD –
27 Buttons for the multi-picture display ("picture
in picture" or "picture next to picture")
Button "PIP/
To switch over the different display modes
Button "Position"
To select the position for the sub-picture in
case of picture-in-picture display
Button "Swap"
To change the picture assignment of the
signal sources in the multi-picture display
28 Button "Zoom" to switch over different picture
formats
29 Button "Power" : same as button
monitor
30 button "Source/ ": same as button "SOURCE"
(3) at the monitor
31 Button "Item": same as button "ITEM" (5) at
the monitor
32 Button "Menu / OK": same as button "MENU"
(4) at the monitor
33 Button "Sleep" for the sleep function (auto-
matic switching to stand-by after an adjusted
time has elapsed): select the time with the
button or deactivate the function
34 Button "Picture" to select different picture
modes
35 Button "Display" to shortly insert information
about the source
to activate and deactivate
DVI HD )
TM input (10)
and
"
(7) at the

2 Safety Notes

The units (monitor and power supply unit) corre-
spond to all relevant directives of the EU and are
therefore marked with .
WARNING The power supply unit uses dan-
gerous mains voltage. Leave serv-
icing to skilled personnel only. Inex-
pert handling may result in electric
shock.
G
The units are suitable for indoor use only. Pro-
tect them against dripping water and splash
water, high air humidity and heat (admissible
ambient temperature range 0 – 40 °C).
G
Do not place any vessels filled with liquid, e. g.
drinking glasses, on the units.
G
To prevent heat accumulation inside the unit
always place the monitor so that a sufficient air
circulation is ensured. The air vents must not
be covered.
G
Do not set the units into operation, and imme-
diately disconnect the mains plug of the power
supply unit from the mains socket if
1. there is visible damage to a unit or the mains
cable,
2. a defect might have occurred after a drop or
similar accident,
3. malfunctions occur.
The units must in any case be repaired by
skilled personnel.
G
Never pull the mains cable to disconnect the
mains plug from the mains socket, always
seize the plug.
G
For cleaning the power supply unit only use a
dry, soft cloth. For cleaning the monitor it is
also possible to use a soft cloth, slightly damp.
Never use chemicals or aggressive deter-
gents. Prior to cleaning disconnect the mains
plug.
G
No guarantee claims for the units and no liabil-
ity for any resulting personal damage or mate-
rial damage will be accepted if the units are
used for other purposes than originally in -
tended, if they are not correctly connected or
operated, or not repaired in an expert way.
If the units are to be put out of operation
definitively, take them to a local recy-
cling plant for a disposal which is not
harmful to the environment.
9