Monacor TFT-1904LED Mode D'emploi page 13

PIP Position (position of the sub-picture)
If the menu item PIP Position has been
selected, press the button "MENU" to acti-
vate it. For the three picture-in-picture dis-
plays the position of the sub-picture in the
main menu can be selected: Left Up (on the
top left), Right Up (on the top right), Left Dn (on
the left at the bottom), Right Dn (on the right at
the bottom). Select the position with the
button or and confirm the selection
with the button "MENU".
PIP Source (source of the sub-picture)
If the menu item PIP Source has been selected,
press the button "MENU" to activate it.
Select the signal source for the sub-picture
with the button or . Press the button
"SOURCE" to deactivate the menu item.
Main picture Selectable for the sub-picture
AV 1 PC, DVI, HD
AV 2 PC, DVI, HD
S-Video PC, DVI, HD
PC AV 1, AV 2, S-Video, DVI, HD
DVI AV 1, AV 2, S-Video, PC
HD AV 1, AV 2, S-Video, PC
PIP Swap (swap of the picture assignment)
If the menu item PIP Swap has been selected,
press the button "MENU" to activate it. The
on-screen menu is exited and the assign-
ment of the sources to main picture and
sub-picture is swapped.
To exit the submenu PIP, press the button
"SOURCE".
Sleep Mode
Via this menu item a time can be defined after
which the monitor is automatically set to
stand-by. If the menu item Sleep Mode has been
selected, press the button "MENU" to activate
it. Select the time (10 minutes ... 180 minutes)
or the setting OFF (function switched off) with
the button or . Confirm the selection with
the button "MENU".
Image Auto Move (automatic picture movement)
To prevent shadow images (= persistence of
previous picture contents, may occur with
longer still pictures), an automatic picture
movement can be activated at regular time
intervals. If the menu item Image Auto Move is
selected, press the button "MENU" to activate
it. Select the time intervals (every 10 minutes
... every 180 minutes) or the setting OFF (func-
tion switched off) with the button
firm the selection with the button "MENU".
Gamma (gamma value)
For brightness correction of the grey scale val-
ues the gamma value may be changed. If the
menu item Gamma has been selected, press the
button "MENU" to activate it. Select the gamma
value (0, 1 or 2) with the button
firm the selection with the button "MENU".
Reset All Setting (factory settings)
If the menu item Reset All Setting has been
selected, press the button "MENU": The mon-
itor is reset to the factory settings and the on-
screen menu is exited.
USB update (firmware update)
This menu item is not required for operation
and exclusively serves for updating the firm -
ware via the USB port (9) if a new firmware
version is available.
The last line of this menu only serves for infor-
mation and cannot be adjusted.
To return to the main menu level, press the but-
ton "SOURCE".
10 Specifications
Diagonal screen size: . 48 cm (19")
Maximum display
resolution: . . . . . . . . . . 1280 × 1024 pixels
Colour system: . . . . . . PAL / NTSC (auto)
Angle of view: . . . . . . . hor. 170°, vert. 160°
Response time: . . . . . 1.3 / 3.7 ms
Brightness: . . . . . . . . . 250 cd / m
Contrast ratio: . . . . . . . 1000 : 1
Colour display: . . . . . . 16.7 million colours
Inputs for the
signal sources: . . . . . . 1 × HDMI
Feed-through outputs
Video: . . . . . . . . . . . 2 × BNC
Audio: . . . . . . . . . . . 2 × RCA
Speaker: . . . . . . . . . . . 2 W
Power supply: . . . . . . . via supplied PSU con-
Ambient temperature: . 0 – 40 °C
Dimensions: . . . . . . . . 425 × 352 × 53 mm
Hole distance for
mounting the bracket: . VESA-100 standard
Weight: . . . . . . . . . . . . 3.7 kg (w/o base)
Subject to technical modification.
or . Con-
or and con-
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
2
TM
1 × DVI-D
1 × VGA
1 × S-Video
2 × BNC
2 × RCA
("AUDIO IN")
1 × 3.5 mm jack
("PC AUDIO IN")
nected to 230 V/50 Hz
(w/o base)
(100 × 100 mm)
® INTERNATIONAL GmbH & Co. KG. No part of this instruction
13