Operating Elements And Connections; Safety Notes; Applications - Monacor security CDM-602 Mode D'emploi

Please unfold page 3. Thus, you will always be able
GB
to see the operating elements and connections
described.

1 Operating Elements and Connections

1 POWER switch
2 LEDs to indicate the operating mode selected with
the button SELECT (3)
3 Button to select the three operating modes; the cor-
responding LED (2) lights up
CH1 channel 1 (signal source 1)
CH2 channel 2 (signal source 2)
AUTO automatic channel switching
4 Power supply jacks for the two signal sources,
12 V /max. 250 mA for each connection
5 Video input 2 (VIDEO IN, yellow) and audio input 2
(AUDIO IN, white) for connection of the second sig-
nal source
6 Video input 1 (VIDEO IN, yellow) and audio input 1
(AUDIO IN, white) for connection of the first signal
source
7 Video output (VIDEO OUT, yellow) and audio out-
put (AUDIO OUT, white) for passing on the fed-
through input signals to another unit
8 Power supply jack (13.5 V /max. 1.2 A) for con-
necting the supplied plug-in power supply unit
9 Volume control
10 Control for adjusting the dwell time (1 – 20 s) for the
automatic channel switching
11 Control for the picture synchronization with vertical
picture rolling
12 Contrast control
13 Brightness control
14 Selector switch CCIR/EIA
button not pressed:
standard CCIR (frame frequency 50 Hz)
button pressed:
standard EIA (frame frequency 60 Hz)

2 Safety Notes

The units (monitor and power supply unit) correspond
to all required directives of the EU and are therefore
marked with .
WARNING The monitor and the power supply unit
operate with hazardous mains voltage.
Leave servicing to skilled personnel
only. Never make any modification on
the units and do not insert anything
through the air vents of the monitor
housing. Inexpert handling may cause
an electric shock hazard.
6
It is essential to observe the following items:
CAUTION! The picture tube of the monitor is
vacuous. In case of mechanical damage there is an
implosion hazard and scattered glass may cause
injuries.
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity, and heat (admissible ambient tempera-
ture range 0 – 40 °C).
Do not place any vessels filled with liquid, e. g. drink-
ing glasses, on the monitor.
The heat being generated in the monitor must be
carried off by air circulation. Therefore, the air vents
at the housing must not be covered.
Do not set the monitor into operation, or immediate-
ly disconnect the power supply unit from the mains
socket if
1. there is visible damage to the monitor or the
power supply unit,
2. a defect might have occurred after a drop or simi-
lar accident,
3. malfunctions occur.
The units must in any case be repaired by skilled
personnel.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the units and no liability for
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not cor-
rectly connected, operated, or not repaired in an
expert way.
If the units are to be put out of operation de-
finitively, take them to a local recycling plant
for a disposal which is not harmful to the envi-
ronment.

3 Applications

The handy B/W monitor CDM-602 is suitable for uni-
versal applications, e. g. in a small video surveillance
system or for multimedia applications. For audio repro-
duction, a small speaker is integrated.
Up to two audio/video sources (e. g. surveillance
camera, video recorder) may be connected which can
be supplied with 12 V
tor. It is possible to switch between the sources either
manually or automatically with adjustable dwell time.
The parallel outputs allow to pass on the audio and
video signals of the selected source to another unit.
Via a selector switch the monitor can be adjusted to the
video standard CCIR or EIA.
operating voltage via the moni-