ST CP1 430 Li 48 Serie Manuel D'utilisation page 113

– Mowing dense, high and/or wet grass.
b. Machine cutting width; wider settings involve high-
er energy consumption.
c. Operator behaviour that should be avoided:
– Switching the machine on and off
frequently whilst working.
– Setting a cutting height that is too
low for the lawn conditions.
– Working at a speed that is too high in relation
to the amount of grass to be removed.
NOTE During use, the battery is protected against total
drainage with a protective device that switches off the ma-
chine and prevents its operation.
To optimise battery power reserve it is always recommend-
ed to:
– Cut the grass when the lawn is dry.
– Cut the grass frequently so that it doesn't grow too tall.
– Set a higher cutting height when the grass is very
tall, then set a lower height and cut the lawn again.
– Do not use the machine in "mulching"
mode with very high grass.
– Use of the "ECO" mode (par. 5.2.4).
If the need arises to use the machine for sessions which ex-
ceed the capability of a standard battery, it is possible to:
– Purchase a second standard battery to immediately
replace the discharged battery, without
compromising the continuity of operations.
– Purchase a battery with an extended power reserve
compared to the standard version (par. 13.2).
7.2.2 Battery removal and recharging
1. Open the battery compartment access hatch and re-
move the safety key.
2. Press the button on the battery (Fig.22.A) and remove
the battery (Fig.22.B).
Insert the battery (Fig.23.B) in its housing in the battery
3.
charger (Fig.23.C).
4. Connect the battery charger to a power socket with the
voltage indicated on the rating plate.
5. Fully charge the battery according to the instructions in
the battery/battery charger booklet.
NOTE The battery is equipped with a protective device
that inhibits recharging if the environmental temperature is
not between 0 and +45 °C.
NOTE The battery can be recharged at any time, even
partially, with no risk of damaging it.
7.2.3 Refitting the battery on the machine
When recharging is completed:
1. Remove the battery from the housing in the battery
charger (do not keep recharging when recharging is
completed).
2. Disconnect the battery charger from the mains power
supply.
Open the battery housing hatch (Fig.24.A), insert the
3.
battery (Fig.24.B) into its housing pressing down until
you hear it click firmly into position, ensuring thus the
electrical contact.
Completely close the hatch again.
7.3 CLEANING
Clean thoroughly following the instructions below every
time it is used.
7.3.1 Cleaning the machine
• Always make sure the air intakes are free of debris.
• Do not spray water onto the motor and electrical compo-
nents, prevent them from getting wet (Fig.26).
• Do not use aggressive liquids to clean the chassis.
• To reduce the risk of fire, keep the engine free of grass,
leaves residues or excessive grease.
• Always keep the levers, display and buttons free of debris.
7.3.2 Cleaning the cutting means assembly
Remove grass debris and mud accumulated inside the
chassis.
For side discharge: remove the discharge chute (if
mounted - par. 6.1.2d.).
7.3.3 Cleaning the grass catcher (Fig.27.A/B)
7.4 NUTS AND BOLTS
Keep all nuts, bolts and screws tight to be sure the equip-
ment is in a safe working condition.
7.5 CLEANING THE AIR FILTER
The filter element must always be kept perfectly clean.
Proceed as follows:
1. Clean around the air filter grid.
2. Unscrew the screw (Fig.28.B) to remove the grid
(Fig.28.A).
3. Remove the filter element (Fig.29.A).
Blow the filter of wash it with water (Fig.29.A) to remove
4.
the dust and residues.
5. Refit the filter element (Fig.29.A) in its housing,
refit the grid and tighten the screw (Fig.28.A) and
(Fig. 28.B).
• Wear heavy duty gloves.
• Hold the machine in the points offering a safe grip, taking
into account the weight and its division.
• Use an appropriate number of people for the weight of
the machine and the characteristics of the vehicle or the
place where it must be placed or collected.
8. OCCASIONAL MAINTENANCE
Before commencing any inspections, cleaning or
maintenance/adjustments on the machine:
• Stop the machine.
• Remove the safety key, (never leave the key inserted or
within the reach of children or unauthorised persons).
• Make sure that all moving parts have come to a complete
stop.
• Allow the motor to cool before storing in an enclosed
space.
• Read the relevant instructions.
• Use suitable clothing, protective gloves and goggles.
8.1 CUTTING MEANS
An improperly sharpened cutting means pulls at the grass
and causes the lawn to turn yellow.
EN - 8